- 您现在的位置：买卖IC网 > PDF目录11815 > XR20M1172IG28 (Exar Corporation)IC UART FIFO I2C/SPI 64B 28TSSOP PDF资料下载
参数资料
| 型号： | XR20M1172IG28 |
| 厂商： | Exar Corporation |
| 文件页数： | 13/55页 |
| 文件大小： | 0K |
| 描述： | IC UART FIFO I2C/SPI 64B 28TSSOP |
| 产品变化通告： | Leaded UART, V&I Obsolescence 11/Apr/2011 |
| 标准包装： | 50 |
| 特点： | * |
| 通道数： | 2，DUART |
| FIFO's： | 64 字节 |
| 规程： | RS485 |
| 电源电压： | 1.62 V ~ 3.63 V |
| 带自动流量控制功能： | 是 |
| 带IrDA 编码器/解码器： | 是 |
| 带故障启动位检测功能： | 是 |
| 带调制解调器控制功能： | 是 |
| 带CMOS： | 是 |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 28-TSSOP |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
XR20M1172
20
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
REV. 1.2.0
2.12
Auto Xon/Xoff (Software) Flow Control
When software flow control is enabled (See Table 15), the M1172 compares one or two sequential receive
data characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the M1172 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the M1172 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the M1172 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters (See Table 15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
selected, the M1172 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the M1172 automatically
sends the Xoff-1,2 via the serial TX output to the remote modem when the RX FIFO reaches the Halt Level
(TCR[3:0]). To clear this condition, the M1172 will transmit the programmed Xon-1,2 characters as soon as RX
FIFO falls down to the Resume Level.
2.13
Special Character Detect
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The M1172 compares each incoming receive character with Xoff-2 data. If a match exists, the received data
will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the
Internal Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison.
2.14
Auto RS485 Half-duplex Control
The auto RS485 half-duplex direction control changes the behavior of the transmitter when enabled by EFCR
bit-4. It also changes the behavior of the transmit empty interrupt (see Table 4). When idle, the auto RS485
half-duplex direction control signal (RTS#) is HIGH for receive mode. When data is loaded into the THR for
transmission, the RTS# output is automatically asserted LOW prior to sending the data. After the last stop bit of
the last character that has been transmitted, the RTS# signal is automatically de-asserted. This helps in turning
around the transceiver to receive the remote station’s response. When the host is ready to transmit next polling
data packet, it only has to load data bytes to the transmit FIFO. The transmitter automatically re-asserts RTS#
(LOW) output prior to sending the data. The polarity of the RTS# output pin can be inverted by setting EFCR[5]
= 1.
2.14.1
Normal Multidrop Mode
Normal multidrop mode is enabled when EFCR bit-0 = 1 and EFR bit-5 = 0 (Special Character Detect
disabled). The receiver is set to Force Parity 0 (LCR[5:3] = ’111’) in order to detect address bytes.
With the receiver initially disabled, it ignores all the data bytes (parity bit = 0) until an address byte is received
(parity bit = 1). This address byte will cause the UART to set the parity error. The UART will generate an LSR
interrupt and place the address byte in the RX FIFO. The software then examines the byte and enables the
receiver if the address matches its slave address, otherwise, it does not enable the receiver.
If the receiver has been enabled, the receiver will receive the subsequent data. If an address byte is received,
it will generate an LSR interrupt. The software again examines the byte and If the address matches its slave
addres, it does not have to anything. If the address does not match its slave address, then the receiver should
be disabled.
相关PDF资料 |
PDF描述 |
|---|---|
| XR20M1170IL28-F | IC UART FIFO I2C/SPI 64B 28QFN |
| MS3110F14-15S | CONN RCPT 15POS WALL MNT W/SCKT |
| MS27472T16B8SA | CONN RCPT 8POS WALL MT W/SCKT |
| VI-B7H-IX-F3 | CONVERTER MOD DC/DC 52V 75W |
| AT32UC3L064-ZAUR | IC MCU AVR32 64K FLASH 48VQFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XR20M1172IG28-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR20M1172IG28-F | 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 28-TSSOP 制造商:Exar Corporation 功能描述:IC, DUAL UART, 16MBPS, 3.63V, 28-TSSOP |
| XR20M1172IG28TR-F | 功能描述:UART 接口集成电路 1.8V 2 Ch 64-byte I2C/SPI UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
| XR20M1172IL32 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO |
| XR20M1172IL32-F | 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。