参数资料
型号: XR20M1172IG28
厂商: Exar Corporation
文件页数: 16/55页
文件大小: 0K
描述: IC UART FIFO I2C/SPI 64B 28TSSOP
产品变化通告: Leaded UART, V&I Obsolescence 11/Apr/2011
标准包装: 50
特点: *
通道数: 2,DUART
FIFO's: 64 字节
规程: RS485
电源电压: 1.62 V ~ 3.63 V
带自动流量控制功能:
带IrDA 编码器/解码器:
带故障启动位检测功能:
带调制解调器控制功能:
带CMOS:
安装类型: 表面贴装
封装/外壳: 28-TSSOP(0.173",4.40mm 宽)
供应商设备封装: 28-TSSOP
包装: 管件
XR20M1172
23
REV. 1.2.0
TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
2.16
Sleep Mode with Auto Wake-Up
The M1172 supports low voltage system designs, hence, a sleep mode is included to reduce its power
consumption when the chip is not actively used.
All of these conditions must be satisfied for both channels of the M1172 to enter sleep mode:
s
no interrupts pending (ISR bit-0 = 1)
s
sleep mode of both channels are enabled (IER bit-4 = 1)
s
modem inputs are not toggling (MSR bits 0-3 = 0)
s
RX input pin is idling HIGH
The M1172 stops its crystal oscillator to conserve power in the sleep mode. User can check the XTAL2 pin for
no clock output as an indication that the device has entered the sleep mode.
The M1172 resumes normal operation by any of the following:
s
a receive data start bit transition (HIGH to LOW)
s
a data byte is loaded to the transmitter, THR or FIFO
s
a change of logic state on any of the modem or general purpose serial inputs: CTS#, DSR#, CD#, RI#
If the M1172 is awakened by any one of the above conditions, it will return to the sleep mode automatically
after all interrupting conditions have been serviced and cleared. If the M1172 is awakened by the modem
inputs, a read to the MSR is required to reset the modem inputs. In any case, the sleep mode will not be
entered while an interrupt is pending. The M1172 will stay in the sleep mode of operation until it is disabled by
setting IER bit-4 to a logic 0.
If the serial clock, serial data, and modem input lines remain steady when the M1172 is in sleep mode, the
maximum current will be in the microamp range as specified in the DC Electrical Characteristics on page 43.
A word of caution: owing to the starting up delay of the crystal oscillator after waking up from sleep mode, the
first few receive characters may be lost. The number of characters lost during the restart also depends on your
operating data rate. More characters are lost when operating at higher data rate. Also, it is important to keep
RX input idling HIGH or “marking” condition during sleep mode to avoid receiving a “break” condition upon the
restart. This may occur when the external interface transceivers (RS-232, RS-485 or another type) are also put
to sleep mode and cannot maintain the “marking” condition. To avoid this, the designer can use a 47k-100k
ohm pull-up resistor on the RX input pin.
相关PDF资料
PDF描述
XR20M1170IL28-F IC UART FIFO I2C/SPI 64B 28QFN
MS3110F14-15S CONN RCPT 15POS WALL MNT W/SCKT
MS27472T16B8SA CONN RCPT 8POS WALL MT W/SCKT
VI-B7H-IX-F3 CONVERTER MOD DC/DC 52V 75W
AT32UC3L064-ZAUR IC MCU AVR32 64K FLASH 48VQFN
相关代理商/技术参数
参数描述
XR20M1172IG28-F 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR20M1172IG28-F 制造商:Exar Corporation 功能描述:IC DUAL UART 16MBPS 3.63V 28-TSSOP 制造商:Exar Corporation 功能描述:IC, DUAL UART, 16MBPS, 3.63V, 28-TSSOP
XR20M1172IG28TR-F 功能描述:UART 接口集成电路 1.8V 2 Ch 64-byte I2C/SPI UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel
XR20M1172IL32 制造商:EXAR 制造商全称:EXAR 功能描述:TWO CHANNEL I2C/SPI UART WITH 64-BYTE FIFO
XR20M1172IL32-F 功能描述:UART 接口集成电路 UART RoHS:否 制造商:Texas Instruments 通道数量:2 数据速率:3 Mbps 电源电压-最大:3.6 V 电源电压-最小:2.7 V 电源电流:20 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装 / 箱体:LQFP-48 封装:Reel