参数资料
| 型号： | XRD9816BCV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 10/53页 |
| 文件大小： | 0K |
| 描述： | IC 16BIT CCD/CIS SIG PROC 48TQFP |
| 标准包装： | 250 |
| 位数： | 16 |
| 通道数： | 3 |
| 电压 - 电源，模拟： | 4.5 V ~ 5.5 V |
| 电压 - 电源，数字： | 3 V ~ 5.5 V |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XRD9814B/9816B
18
Rev. 1.00
(Correlated Double Sampling)
Correlated double sampling is a technique used to level
shift and acquire CCD output signals whose informa-
tion is equal to the difference between consecutive
reference (black) and signal (video) samples. The CDS
process consists of three steps:
1)
Sampling and holding the reference black level.
2)
Sampling the video level.
3)
Subtracting the two samples to extract the video
information.
Once the video information has been extracted it can
be processed further through amplification and/or off-
set adjustment. Since system noise is also stored and
subtracted during the CDS process, signals with band-
widths less than half the sampling frequency will be
substantially attenuated.
In order to reject higher frequency power supply noise
which is not attenuated near the sampling frequency
the XRD9814B/9816B utilizes a fully differential input
structure.
Since the CDS process uses AC coupled inputs the
coupling capacitor must be charged to the common-
mode range of the analog front-end. This can be
accomplished by clamping the coupling capacitor to
the internal clamp voltage when the CCD is at a
reference level. This clamp may occur during each
pixel (Pixel Clamp), or at the beginning of each line
(CDS Line Clamp). If CDS Line Clamp mode is used the
input buffer (configuration register #1, PB1) must be
enabled to eliminate the effects of input bias current.
If Pixel mode is selected the input buffer is not required
or recommended.
3-Channel CDS Mode
This mode allows simultaneous CDS of the red, green
and blue inputs . Black-level sampling occurs on each
pixel and is equal to the width of the BSAMP sampling
input. The black level is held on the falling edge of
BSAMP and the PGA will immediately begin to track
the signal input until the falling edge of VSAMP.
Two VSAMP timing modes are supported to allow
additional flexibility in the VSAMP pulse width (see
timing diagrams). At the end of the video sampling
phase the difference between the reference and video
levels is inverted, amplified and offset depending on
the contents of the PGA gain and offset registers. The
RGB channels are then sequentially converted by a
high speed A/D converter. A/D converter data appears
on the data output bus after 7 ADCCLK cycles. The
green channel is synchronized on the rising edge of the
first ADCCLK after the falling edge of VSAMP. The
power-up default mode is for CDS sampling a CCD
input (Pixel Clamp, Inverting Input, No Input Buffer).
1-Channel CDS Mode
The 1-Channel CDS mode allows high-speed acquisi-
tion and processing of a single channel. The timing,
clamp and buffer configurations are similar to the 3-
channel mode described previously. To select a single
channel input the color bits of configuration register 1
must be set to the appropriate value. The A/D input will
begin to track the selected color input on the next
positive edge of ADCCLK. If the configuration is
toggled from single color to 3-channel mode RGB
scanning will not occur until the circuit is
resynchronized on the falling edge of VSAMP.
相关PDF资料 |
PDF描述 |
|---|---|
| XRD9818ACGTR | IC 16B CCD/CIS SIG PROC 28TSSOP |
| XRD9824ACU | IC 14B CCD/CIS SIG PROC 20SSOP |
| XRD9825ACU | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9826ACUTR | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9827ACU | IC 12B CCD/CIS SIG PROC 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRD9816EVAL | 功能描述:数据转换 IC 开发工具 Eval Board for XRD9816BCV RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| XRD9818 | 制造商:EXAR 制造商全称:EXAR 功能描述:3-CHANNEL 16-BIT LINEAR CCD/CIS SENSOR SIGNAL PROCESSOR |
| XRD9818ACG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| XRD9818ACG-F | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| XRD9818ACGTR | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。