参数资料
| 型号： | XRD9816BCV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 6/53页 |
| 文件大小： | 0K |
| 描述： | IC 16BIT CCD/CIS SIG PROC 48TQFP |
| 标准包装： | 250 |
| 位数： | 16 |
| 通道数： | 3 |
| 电压 - 电源，模拟： | 4.5 V ~ 5.5 V |
| 电压 - 电源，数字： | 3 V ~ 5.5 V |
| 封装/外壳： | 48-TQFP |
| 供应商设备封装： | 48-TQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页
XRD9814B/9816B
14
Rev. 1.00
GENERAL DESCRIPTION
The XRD9814B/9816B contains all of the circuitry
required to create a complete 3-channel signal proces-
sor /digitizer for use in CCD/CIS imaging systems.
Each channel includes a correlated double sampler
(CDS), programmable gain amplifier (PGA) and chan-
nel offset adjustment. The input stage can also be
configured for use with inverting/non-inverting, AC or
DC coupled signals. In order to maximize flexibility, the
specific operating mode is programmable through two
configuration registers. In addition, the gain and offset
of each channel can be independently programmed
through separate gain and offset registers. Configura-
tion register data is loaded serially through a 3-pin
serial interface. Specific details for register writes are
detailed below. After signal conditioning the three PGA
outputs are digitized by a 14-bit/16-bit A/D converter.
Writing Registers Data
The XRD9814B/9816B utilizes eight 10-Bit registers to
store configuration, gain and offset information. Regis-
ter data is written through the 3-pin serial interface
consisting of SDI (serial data input), SCLK (serial shift
clock) and LOAD (positive edge write enable). A write
consists of pulling LOAD low, shifting in 3 bits of
address (MSB first) and 10 bits of data (MSB first).
Data is written on the rising edge of SCLK and the last
13 bits are latched. The timing for writing to registers
is shown in Figure 17 and 18.
When INSEL=0, SCLK, SDI, and LOAD pins are active
for serial programming.
When INSEL=1, SCLK and SDI pins are inactive, and
the serial programming is done through I/O pins DB12/
DB14 and DB13/DB15 while LOAD pin is low.
Configuration Register #1
The bit assignment and definition for this register is
detailed in the Configuration Register #1 Definition
Table (Table 2). The primary purpose of this register is
to configure the analog input blocks for CCD or S/H
operation.
Clamp Mode
The clamp mode setting determines the conditions
when the internal clamp is enabled (see Table 5). The
pixel and CCD line-clamp modes are used to DC-
restore AC coupled CCD input signals to the PGA
common-mode input voltage while using correlated
double sampling. S/H line mode should be used to DC-
restore AC coupled inputs which do not utilize corre-
lated double sampling and have only one control input
(VSAMP). No-clamp mode should be used for DC
coupled S/H inputs.
Pixel Mode (CCD with CDS)
The input clamp is active each pixel period with a
pulse-width determined by the Black- level Sampling
Input (BSAMP). The position of BSAMP can be opti-
mized to eliminate the effects of the CCD reset pulse.
Since the input capacitor is recharged to the clamp
voltage on each pixel, common-mode droop errors are
eliminated.
CCD Line Mode (CCD with CDS)
The input clamp is enabled only at the beginning of the
line by gating
BSAMP with LCLMP.
Gating with
LCLMP maintains the ability to position the clamp
pulse (BSAMP) away from the CCD reset for varying
LCLMP position and width. Since the input capacitor
is clamped only at the beginning of each line a larger
input capacitor is required to satisfy the common-mode
input requirements of the analog front-end. (See Cou-
pling Capacitor Requirements.) The input buffer should
be enabled in this mode (PB1=1, Register #1).
S/H Line Mode (S/H with AC Coupling)
The S/H Line mode clamp is used to DC-restore AC
coupled inputs which do not utilize CDS. VSAMP is
used to sample and hold the input signal and LCLMP
performs the clamp function. This differs from the CDS
line and pixel modes which use BSAMP to clamp to the
reference level and VSAMP to hold the video input. The
input buffer should be enabled in this mode (PB1=1,
Register #1).
相关PDF资料 |
PDF描述 |
|---|---|
| XRD9818ACGTR | IC 16B CCD/CIS SIG PROC 28TSSOP |
| XRD9824ACU | IC 14B CCD/CIS SIG PROC 20SSOP |
| XRD9825ACU | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9826ACUTR | IC 16B CCD/CIS SIG PROC 20SSOP |
| XRD9827ACU | IC 12B CCD/CIS SIG PROC 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRD9816EVAL | 功能描述:数据转换 IC 开发工具 Eval Board for XRD9816BCV RoHS:否 制造商:Texas Instruments 产品:Demonstration Kits 类型:ADC 工具用于评估:ADS130E08 接口类型:SPI 工作电源电压:- 6 V to + 6 V |
| XRD9818 | 制造商:EXAR 制造商全称:EXAR 功能描述:3-CHANNEL 16-BIT LINEAR CCD/CIS SENSOR SIGNAL PROCESSOR |
| XRD9818ACG | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| XRD9818ACG-F | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
| XRD9818ACGTR | 功能描述:模数转换器 - ADC RoHS:否 制造商:Texas Instruments 通道数量:2 结构:Sigma-Delta 转换速率:125 SPs to 8 KSPs 分辨率:24 bit 输入类型:Differential 信噪比:107 dB 接口类型:SPI 工作电源电压:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:VQFN-32 |
发布紧急采购，3分钟左右您将得到回复。