参数资料
| 型号： | XRT73LC04AIV-F |
| 厂商： | Exar Corporation |
| 文件页数： | 55/64页 |
| 文件大小： | 0K |
| 描述： | IC LIU E3/DS3/STS-1 4CH 144LQFP |
| 标准包装： | 60 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 4/4 |
| 规程： | DS3，E3，STS-1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LQFP |
| 供应商设备封装： | 144-LQFP（20x20） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
XRT73LC04A
55
REV. 1.0.2
4 CHANNEL DS3/E3/STS-1 LINE INTERFACE UNIT
Bit D4 - Reserved
Bit D3 - Reserved
Bit D2 - ALOSDIS_(n) (Analog LOS Disable -
Channel(n))
This Read/Write bit-field is used to enable or disable
the Channel(n) Analog LOS Detector.
Writing a "0" to this bit-field enables the Analog LOS
Detector. Writing a "1" to this bit-field disables the
Analog LOS Detector.
NOTE: If the Analog LOS Detector is disabled, then the
RLOS input pin is only asserted by the DLOS (Digital LOS
Detector).
Bit D1 - DLOSDIS_(n) (Digital LOS Disable - Chan-
nel(n))
This Read/Write bit-field to used to enable or disable
the Channel(n) Digital LOS Detector .
Writing a "0" to this bit-field enables the Digital LOS
Detector. Writing a "1" to this bit-field disables the
Digital LOS Detector.
NOTE: If the Digital LOS Detector is disabled, then the
RLOS input pin is only asserted by the ALOS (Analog LOS
Detector).
Bit D0 - REQEN_(n) (Receive Equalization Enable
- Channel(n))
This Read/Write bit-field is used to enable or disable
the internal Channel(n) Receive Equalizer.
Writing a "1" to this bit-field enables the Internal
Equalizer. Writing a "0" to this bit-field disables the
Internal Equalizer.
5.2.4
Command Register CR3-(n)
The bit-format and default values for Command Reg-
ister CR3-(n) are listed below followed by the function
of each of these bit fields.
Bit D4 - SR/DR (Single-Rail/Dual-Rail Data Output
- Channel(n))/(B3ZS/HDB3 Encoder/Decoder-Dis-
able - Channel(n))
This Read/Write bit-field is used to configure Chan-
nel(n) to output the received data from the Remote
Terminal in a binary or Dual-Rail format and Enable
or Disable the B3ZS/HDB3 Encoder and Decoder
blocks.
Writing a "1" to this bit-field enables the B3ZS/HDB3
Encoder and Decoder blocks. Writing a "0" to this bit-
field disables the B3ZS/HDB3 Encoder and Decoder
blocks.
NOTE: This Encoder/Decoder performs HDB3 Encoding/
Decoding if the XRT73LC04A is operating in the E3 Mode.
Otherwise, it performs B3ZS Encoding/Decoding.
.Writing a "1" to this bit-field also configures Chan-
nel(n) to output data to the Terminal Equipment in a
binary (Single-Rail) format via the RPOS_(n) output
pin, RNEG_(n) is grounded. Writing a "0" to this bit-
field configures Channel(n) to output data to the Ter-
minal Equipment in a Dual-Rail format via both the
RPOS_(n) and RNEG_(n) output pins.
Bit D3 - LOSMUT_(n) (Recovered Data Muting,
during LOS Condition - Channel(n))
This Read/Write bit-field is used to configure Chan-
nel(n) to not output any recovered data from the line
while it is declaring an LOS condition.
Writing a "0" to this bit-field configures the chip to out-
put recovered data even while the XRT73LC04A is
declaring an LOS condition. Writing a "1" to this bit-
field configures the chip to NOT output the recovered
data while an LOS condition is being declared.
NOTE: In this mode, RPOS_(n) and RNEG_(n) is set to "0",
asynchronously.
Bit D2 - RxOFF (Receive Section - Shut OFF Se-
lect)
This Read/Write bit-field is used to shut-off the Re-
ceive Sections. The purpose is to conserve power
consumption when this device is the back-up device
in a Redundancy System.
Writing a "1" into this bit-field shuts off the Receive
Sections. Writing a "0" into this bit-field turns on the
Receive Sections.
Bit D1 - RxClk_(n)INV (Invert RxClk_(n))
This Read/Write bit-field is used to configure the
Channel(n) Receiver to output the recovered data on
either the rising edge or the falling edge of the
RxClk_(n) clock signal.
Writing a "0" to this bit-field configures the Receiver to
output the recovered data on the rising edge of the
RxClk_(n) output signal. Writing a "1" to this bit-field
configures the Receiver to output the recovered data
on the falling edge of the RxClk_(n) output signal.
Bit D0 - Reserved
COMMAND REGISTER CR3-(n)
D4
D3
D2
D1
D0
SR/DR_(n)
LOSMUT_(n)
RxOFF
RxClk_(n)INV
Reserved
0
相关PDF资料 |
PDF描述 |
|---|---|
| XRT73R06IB-F | IC LIU E3/DS3/STS-1 6CH 217BGA |
| XRT73R12IB-L | IC LIU E3/DS3/STS-1 12CH 420TBGA |
| XRT75L00DIV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L00IV-F | IC LIU E3/DS3/STS-1 SGL 52TQFP |
| XRT75L02DIV-F | IC LIU E3/DS3/STS-1 2CH 100TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT73R06 | 制造商:EXAR 制造商全称:EXAR 功能描述:SIX CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
| XRT73R06ES | 功能描述:网络控制器与处理器 IC RoHS:否 制造商:Micrel 产品:Controller Area Network (CAN) 收发器数量: 数据速率: 电源电流（最大值）:595 mA 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:PBGA-400 封装:Tray |
| XRT73R06IB | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT73R06IB-F | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT73R12 | 制造商:EXAR 制造商全称:EXAR 功能描述:TWELVE CHANNEL E3/DS3/STS-1 LINE INTERFACE UNIT |
发布紧急采购，3分钟左右您将得到回复。