参数资料
型号: XRT75VL00D
厂商: Exar Corporation
英文描述: E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
中文描述: E3/DS3/STS-1线路接口单元与SONET DESYNCHRONIZER
文件页数: 49/92页
文件大小: 836K
代理商: XRT75VL00D
XRT75VL00D
REV. 1.0.3
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
48
this SDH signal arrives at the remote PTE, this DS3 or E3 signal will then be extracted from the SDH signal,
and will be output to some other DS3/E3 Terminal Equipment for further processing.
Figure 30 presents an illustration of this approach to transporting DS3 data over a SONET Network
As mentioned above a DS3 or E3 signal will be asynchronously mapped into a SONET or SDH signal and then
transported over the SONET or SDH network. At the remote PTE this DS3 or E3 signal will be extracted (or
de-mapped) from this SONET or SDH signal, where it will then be routed to DS3 or E3 terminal equipment for
further processing.
In order to insure that this "de-mapped" DS3 or E3 signal can be routed to any industry-standard DS3 or E3
terminal equipment, without any complications or adverse effect on the network, the Telcordia and ITU-T
standard committees have specified some limits on both the Intrinsic Jitter and Wander that may exist within
these DS3 or E3 signals as they are de-mapped from SONET/SDH. As a consequence, all PTEs that maps
and de-mapped DS3/E3 signals into/from SONET/SDH must be designed such that the DS3 or E3 data that is
de-mapped from SONET/SDH by these PTEs must meet these Intrinsic Jitter and Wander requirements.
As mentioned above, the LIU can assist the System Designer (of SONET/SDH PTE) by ensuring that their
design will meet these Intrinsic Jitter and Wander requirements.
This section of the data sheet will present the following information to the user.
Some background information on Mapping DS3/E3 signals into SONET/SDH and de-mapping DS3/E3
signals from SONET/SDH.
A brief discussion on the causes of jitter and wander within a DS3 or E3 signal that mapped into a SONET/
SDH signal, and is transported across the SONET/SDH Network.
A brief review of these Intrinsic Jitter and Wander requirements in both SONET and SDH applications.
A brief review on the Intrinsic Jitter and Wander measurement results (of a de-mapped DS3 or E3 signal)
whenever the LIU device is used in a system design.
A detailed discussion on how to design with and configure the LIU device such that the end-system will meet
these Intrinsic Jitter and Wander requirements.
FIGURE 30. A SIMPLE ILLUSTRATION OF A DS3 SIGNAL BEING MAPPED INTO AND TRANSPORTED OVER THE SONET
NETWORK
PTE
SONET
Network
DS3 Data
相关PDF资料
PDF描述
XRT83SL34IV QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XRT83SL34 QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
XS2F-A422-90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-A90-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
XS2F-A422-AB0-A 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET
相关代理商/技术参数
参数描述
XRT75VL00D_08 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET
XRT75VL00D1V-F 制造商:Exar Corporation 功能描述:
XRT75VL00DES 功能描述:时钟合成器/抖动清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75VL00DIV 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel
XRT75VL00DIV-F 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel