- 您现在的位置：买卖IC网 > PDF目录206198 > XRT75VL00D (Exar Corporation) E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER PDF资料下载
参数资料
| 型号： | XRT75VL00D |
| 厂商： | Exar Corporation |
| 英文描述： | E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER |
| 中文描述： | E3/DS3/STS-1线路接口单元与SONET DESYNCHRONIZER |
| 文件页数： | 50/92页 |
| 文件大小： | 836K |
| 代理商： | XRT75VL00D |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页当前第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页
XRT75VL00D
E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET DESYNCHRONIZER
REV. 1.0.3
49
In a SONET system, the relevant specification requirements for Intrinsic Jitter and Wander (within a DS3 signal
that is mapped into and then de-mapped from SONET) are listed below.
Telcordia GR-253-CORE Category I Intrinsic Jitter Requirements for DS3 Applications (Section 5.6), and
ANSI T1.105.03b-1997 - SONET Jitter at Network Interfaces - DS3 Wander Supplement
In general, there are three (3) sources of Jitter and Wander within an asynchronously-mapped DS3 signal that
the system designer must be aware of. These sources are listed below.
Mapping/De-Mapping Jitter
Pointer Adjustments
Clock Gapping
Each of these sources of jitter/wander will be defined and discussed in considerable detail within this Section.
In order to accomplish all of this, this particular section will discuss all of the following topics in details.
How DS3 data is mapped into SONET, and how this mapping operation contributes to Jitter and Wander
within this "eventually de-mapped" DS3 signal.
How this asynchronously-mapped DS3 data is transported throughout the SONET Network, and how
occurrences on the SONET network (such as pointer adjustments) will further contributes to Jitter and
Wander within the "eventually de-mapped" DS3 signal.
A review of the Category I Intrinsic Jitter Requirements (per Telcordia GR-253-CORE) for DS3 applications
A review of the DS3 Wander requirements per ANSI T1.105.03b-1997
A review of the Intrinsic Jitter and Wander Capabilities of the LIU in a typical system application
An in-depth discussion on how to design with and configure the LIU to permit the system to the meet the
above-mentioned Intrinsic Jitter and Wander requirements
NOTE: An in-depth discussion on SDH De-Sync Applications will be presented in the next revision of this data sheet.
9.2
MAPPING/DE-MAPPING JITTER/WANDER
Mapping/De-Mapping Jitter (or Wander) is defined as that intrinsic jitter (or wander) that is induced into a DS3
signal by the "Asynchronous Mapping" process.
This section will discuss all of the following aspects of
Mapping/De-Mapping Jitter.
How DS3 data is mapped into an STS-1 SPE
How frequency offsets within either the DS3 signal (being mapped into SONET) or within the STS-1 signal
itself contributes to intrinsic jitter/wander within the DS3 signal (being transported via the SONET network).
9.2.1
HOW DS3 DATA IS MAPPED INTO SONET
Whenever a DS3 signal is asynchronously mapped into SONET, this mapping is typically accomplished by a
PTE accepting DS3 data (from some remote terminal) and then loading this data into certain bit-fields within a
given STS-1 SPE (or Synchronous Payload Envelope).
At this point, this DS3 signal has now been
asynchronously mapped into an STS-1 signal. In most applications, the SONET Network will then take this
particular STS-1 signal and will map it into "higher-speed" SONET signals (e.g., STS-3, STS-12, STS-48, etc.)
and will then transport this asynchronously mapped DS3 signal across the SONET network, in this manner. As
this "asynchronously-mapped" DS3 signal approaches its "destination" PTE, this STS-1 signal will eventually
be de-mapped from this STS-N signal. Finally, once this STS-1 signal reaches the "destination" PTE, then this
asynchronously-mapped DS3 signal will be extracted from this STS-1 signal.
9.2.1.1
A Brief Description of an STS-1 Frame
In order to be able to describe how a DS3 signal is asynchronously mapped into an STS-1 SPE, it is important
to define and understand all of the following.
The STS-1 frame structure
The STS-1 SPE (Synchronous Payload Envelope)
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83SL34IV | QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL34 | QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XS2F-A422-90-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
| XS2F-A422-A90-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
| XS2F-A422-AB0-A | 4 CONTACT(S), POLYBUTYLENE TEREPHTHALATE, FEMALE, CIRCULAR CONNECTOR, CLAMP, SOCKET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT75VL00D_08 | 制造商:EXAR 制造商全称:EXAR 功能描述:E3/DS3/STS-1 LINE INTERFACE UNIT WITH SONET |
| XRT75VL00D1V-F | 制造商:Exar Corporation 功能描述: |
| XRT75VL00DES | 功能描述:时钟合成器/抖动清除器 1CHT3/E3/STS1LIU+ DESYNC 3.3V DRV VER RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75VL00DIV | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT75VL00DIV-F | 功能描述:时钟合成器/抖动清除器 3.3V 1 CH E3/DS3/STS W/SONET DE-SYNCH RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。