- 您现在的位置：买卖IC网 > PDF目录10009 > XRT83SL30IVTR-F (Exar Corporation)IC LIU T1/E1/J1 SGL 64TQFP PDF资料下载
参数资料
| 型号： | XRT83SL30IVTR-F |
| 厂商： | Exar Corporation |
| 文件页数： | 6/76页 |
| 文件大小： | 0K |
| 描述： | IC LIU T1/E1/J1 SGL 64TQFP |
| 标准包装： | 1,000 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 1/1 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-TQFP（10x10） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页当前第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页
XRT83SL30
11
SINGLE-CHANNEL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR
REV. 1.0.1
REDUNDANCY SUPPORT
SIGNAL NAME
PIN #
TYPE
DESCRIPTION
DMO
11
O
Driver Failure Monitor
This pin transitions "High" if a short circuit condition is detected in the trans-
mit driver, or no transmit output pulse is detected for more than 128 TCLK
cycles.
TERMINATIONS
SIGNAL NAME
PIN #
TYPE
DESCRIPTION
GAUGE
49
I
Twisted Pair Cable Wire Gauge Select
In Hardware Mode, connect this pin "High" to select 26 Gauge wire. Connect this pin
“Low” to select 22 and 24 gauge wire.
NOTE: Internally pulled “Low” with a 50k
resistor.
TRATIO
26
I
Transmitter Transformer Ratio Select
In Hardware Mode, in external termination mode (TXTSEL = “0”), setting this pin "High"
selects a transformer ratio of 1:2 for the transmitter. A "Low" on this pin sets the transmit-
ter transformer ratio to 1:2.45. In the internal termination mode the transmitter trans-
former ratio is permanently set to 1:2 and the state of this pin is ignored.
NOTE: Internally pulled "Low" with a 50k
resistor.
RXTSEL
44
I
Receiver Termination Select
In Hardware Mode when this pin is “Low” the receive line termination is determined only
by the external resistor. When “High”, the receive termination is realized by internal
resistors or the combination of internal and external resistors according to RXRES[1:0].
These conditions are described in the following table:
In Host Mode bit 7 in Control Register 1 (01h) determines if the if the receiver termina-
tion is external or internal. The function of RXTSEL can be transferred to the harware pin
by setting TERCNTL bit (bit 4)
NOTE: This pin is internally pulled "Low" with a 50k
resistor.
TXTSEL
45
I
Transmit Termination Select
In Hardware Mode when this pin is “Low” the transmit line termination is determined
only by external resistor. When “High”, the transmit termination is realized only by an
internal resistor. These conditions are summarized in the following table:
NOTE: This pin is internally pulled "Low" with a 50k
resistor.
RXTSEL
RX Termination
0
1
External
Internal
TXTSEL
TX Termination
0
1
External
Internal
相关PDF资料 |
PDF描述 |
|---|---|
| XRT7298IWTR | IC LINE TX DS3/STS-1 E3 28SOJ |
| VE-BNT-MX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| VE-BNP-MX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| LTC1334CNW | IC CMOS TXRX MULTIPROTOCOL 28DIP |
| VE-BNN-MX-B1 | CONVERTER MOD DC/DC 18.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SL314 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314_05 | 制造商:EXAR 制造商全称:EXAR 功能描述:14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT |
| XRT83SL314ES | 功能描述:LIN 收发器 14 CHT1/E1 LIUSH RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
| XRT83SL314IB | 功能描述:外围驱动器与原件 - PCI RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL314IB-F | 功能描述:LIN 收发器 RoHS:否 制造商:NXP Semiconductors 工作电源电压: 电源电流: 最大工作温度: 封装 / 箱体:SO-8 |
发布紧急采购，3分钟左右您将得到回复。