参数资料
| 型号： | XRT83SL314IB-L |
| 厂商： | Exar Corporation |
| 文件页数： | 41/83页 |
| 文件大小： | 0K |
| 描述： | IC LIU SH T1/E1/J1 14CH 304TBGA |
| 标准包装： | 27 |
| 类型： | 线路接口装置（LIU） |
| 驱动器/接收器数： | 14/14 |
| 规程： | T1，E1，J1 |
| 电源电压： | 3.135 V ~ 3.465 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 304-LBGA |
| 供应商设备封装： | 304-TBGA（31x31） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页
XRT83SL314
xr
REV. 1.0.1
14-CHANNEL T1/E1/J1 SHORT-HAUL LINE INTERFACE UNIT
43
5.1
The Microprocessor Interface Block Signals
The LIU may be configured into different operating modes and have its performance monitored by software
through a standard microprocessor using data, address and control signals.
These interface signals are
described below in Table 15, Table 16, and Table 17. The microprocessor interface can be configured to
operate in Intel mode or Motorola mode. When the microprocessor interface is operating in Intel mode, some
of the control signals function in a manner required by the Intel 80xx family of microprocessors. Likewise, when
the microprocessor interface is operating in Motorola mode, then these control signals function in a manner as
required by the Motorola Power PC family of microprocessors. (For using a Motorola 68K asynchronous
processor, see Figure 41 and Table 20) Table 15 lists and describes those microprocessor interface signals
whose role is constant across the two modes. Table 16 describes the role of some of these signals when the
microprocessor interface is operating in the Intel mode. Likewise, Table 17 describes the role of these signals
when the microprocessor interface is operating in the Motorola Power PC mode.
TABLE 15: XRT84L314 MICROPROCESSOR INTERFACE SIGNALS THAT EXHIBIT CONSTANT ROLES IN BOTH INTEL
AND
MOTOROLA MODES
PIN NAME
TYPE
DESCRIPTION
PTS[2:0]
I
Microprocessor Interface Mode Select Input pins
These three pins are used to specify the microprocessor interface mode. The relationship
between the state of these three input pins, and the corresponding microprocessor mode is
presented in Table 14.
DATA[7:0]
I/O
Bi-Directional Data Bus for register "Read" or "Write" Operations.
ADDR[10:8]
I
Three-Bit Address Bus Inputs
The 3 MSBs of the address bits are used as a chip select decoder. The state of these 3 pins
enable the Chip Selects for additional LIU devices.
NOTE: See the 84-Channel Application Section of this datasheet.
ADDR[7:0]
I
Eight-Bit Address Bus Inputs
The XRT83SL314 LIU microprocessor interface uses a direct address bus. This address bus
is provided to permit the user to select an on-chip register for Read/Write access.
CS
I
Chip Select Input
This active low signal selects the microprocessor interface of the XRT83SL314 LIU and
enables Read/Write operations with the on-chip register locations.
TABLE 16: INTEL MODE: MICROPROCESSOR INTERFACE SIGNALS
XRT83SL314
PIN NAME
INTEL
EQUIVALENT PIN
TYPE
DESCRIPTION
ALE_TS
ALE
I
Address-Latch Enable: This active high signal is used to latch the contents on
the address bus ADDR[7:0]. The contents of the address bus are latched into the
ADDR[7:0] inputs on the falling edge of ALE.
RD_WE
RD
I
Read Signal: This active low input functions as the read signal from the local
P.
When this pin is pulled “Low” (if CS is “Low”) the LIU is informed that a read oper-
ation has been requested and begins the process of the read cycle.
WR_R/W
WR
I
Write Signal: This active low input functions as the write signal from the local
P.
When this pin is pulled “Low” (if CS is “Low”) the LIU is informed that a write
operation has been requested and begins the process of the write cycle.
RDY_TA
RDY
O
Ready Output: This active low signal is provided by the LIU device. It indicates
that the current read or write cycle is complete, and the LIU is waiting for the next
command.
相关PDF资料 |
PDF描述 |
|---|---|
| XRT83SL34IV-F | IC LIU T1/E1/J1 QUAD 128TQFP |
| XRT83SL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VL38IB-F | IC LIU SH T1/E1/J1 OCTAL 225BGA |
| XRT83VSH28IB | IC LIU SH E1 OCTAL 225BGA |
| XRT83VSH314IB-F | IC LIU SH T1/E1/J1 14CH 304TBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| XRT83SL34 | 制造商:EXAR 制造商全称:EXAR 功能描述:QUAD T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
| XRT83SL34ES | 功能描述:外围驱动器与原件 - PCI 4 CHT1/E1 LIUSH RoHS:否 制造商:PLX Technology 工作电源电压: 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:FCBGA-1156 封装:Tray |
| XRT83SL34IV | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT83SL34IV-F | 功能描述:时钟合成器/抖动清除器 RoHS:否 制造商:Skyworks Solutions, Inc. 输出端数量: 输出电平: 最大输出频率: 输入电平: 最大输入频率:6.1 GHz 电源电压-最大:3.3 V 电源电压-最小:2.7 V 封装 / 箱体:TSSOP-28 封装:Reel |
| XRT83SL38 | 制造商:EXAR 制造商全称:EXAR 功能描述:OCTAL T1/E1/J1 SH TRANSCEIVER WITH CLOCK RECOVERY AND JITTER ATTENUATOR |
发布紧急采购，3分钟左右您将得到回复。