- 您现在的位置：买卖IC网 > PDF目录18521 > 0621005110 (Molex Inc)TOOL INSERT SIGNAL CONTACT PDF资料下载
参数资料
| 型号： | 0621005110 |
| 厂商： | Molex Inc |
| 文件页数： | 11/27页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT SIGNAL CONTACT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-5110 62100-5110 621005110 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
5. Using the application tool and an appropriate press, seat the vertical power module until there is less than
0.10mm (.004 in) clearance between the bottom of the plastic housing and the surface of the printed circuit
board.
CAUTION : To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
DAUGHTERCARD
Right Angle Power Module Press-In Tooling
Depending on the number of connectors to be installed and/or
the press used, this tool can be used alone or with a group of
press-in tools, mounted in a 62201-95XX holder (ordered
separately). See Figure 2-13 and 2-14.
1. If the tooling holder is being used, slide the Press-In Tools
into the tooling holder in the proper order. The Press-In
Tools are keyed so that they cannot be put in backwards.
2. Tighten the M3 set screws against the Press-In Tool using
PRESS-IN TOOL
RIGHT ANGLE
POWER MODULE
PRESS-IN TOOL
PCB REF
the following setups:
One (1) set screw is used against the Press-In Tool
under 10mm guide module.
Two (2) set screws evenly spaced on a 10mm wide
Press-In Tool.
At least three (3) set screws evenly spaced on a
D’CARD
RIGHT ANGLE POWER MODULE
Figure 2-13
STAND-ALONE
25mm wide Press-In Tool.
3. Carefully insert, by hand, the power module(s) into the printed
circuit board hole pattern.
4. Place the application tool on top of the power module with the
back guide surface of the tool against the back of the power
module. See Figure 2-14.
5. Using the application tool and an appropriate press, seat the
power module until there is less than 0.10mm (.004 in)
clearance between the bottom of the plastic housing and the
TOOLING HOLDER
62201-95XX
RIGHT ANGLE
POWER MODULE and
D’CARD PRESS-IN TOOL
REF
surface of the printed circuit board. See Figure 2-15.
0.10mm (0.004”)
Maximum
Figure 2-15
PCB REF
D’CARD
RIGHT ANGLE POWER MODULE
Figure 2-14
Right angle power module is seated
alongside the Daughtercard signal module.
For ganged power modules, additional power
module press-in-tools may be needed;
see sales drawings for ganged product
dimensions.
CAUTION : To prevent injury, never operate any press without the guards in place. Refer to the press
manufacturer’s instruction manual.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 11 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| ABMM-14.7456MHZ-B2-T | CRYSTAL 14.7456MHZ 18PF SMD |
| B32520C3103K189 | FILM CAP 0.0100UF 10% 250V |
| 1624146-2 | POT 470K OHM 0.4W 20% SIDE FLAT |
| 1624144-2 | POT 47K OHM 0.4W 20% SIDE FLAT |
| ASA1-3.6864MHZ-L-T | OSC 3.6864 MHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621005200 | 功能描述:MICRO TCA REMOVAL TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0621005300 | 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL - Bulk |
| 0621005400 | 制造商:Molex 功能描述:CONNECTOR SYSTEM TERMINAL REMOVAL TOOL 制造商:Molex 功能描述:TERMINAL REMOVAL TOOL - Bulk |
| 0621005700 | 功能描述:AMC B+ REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0621005800 | 功能描述:IMPACT REPAIR TOOL - BACKPLANE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。