- 您现在的位置：买卖IC网 > PDF目录18521 > 0621005110 (Molex Inc)TOOL INSERT SIGNAL CONTACT PDF资料下载
参数资料
| 型号： | 0621005110 |
| 厂商： | Molex Inc |
| 文件页数： | 8/27页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT SIGNAL CONTACT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-5110 62100-5110 621005110 |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
1. Along the lower edge of the tooling holder is a row of
M3 set screws, (See Figure 2-2), loosen these a few
turns so that they do not protrude into the inside of the
holder.
TYPICAL INSERTION
MODULES
HOLDER
KEYWAY
Figure 2-2
M3 SET SCREW
Figure 2-3
MOUNTING INSERT MODULE IN A MOUNTING BLOCK
TOOLING HOLDER
2. Slide the insertion modules into the tooling holder in the proper
order. See Figure 2-3. The modules are keyed so that they
cannot be put in backwards.
3. Now tighten the M3 set screws against the modules with two (2)
set screws evenly spaced on a 10mm header insertion module and
at least three (3) set screws evenly spaced on a 25mm header
insertion module. Figure 2-4 shows a typical completed assembly.
CAUTION: Do not over tighten the setscrews; this could damage the
insertion tool.
NOTE: See Section 4 for details on selecting modules and Press-In tools
combinations.
M3 x 8mm LONG
SET SCREWS (3)
EVENLY SPACED
Figure 2-4
TYPICAL INSERTION
TOOL ASSEMBLY
2.4 Operation
LOCATING
PIN
PC BOARD
LOCATING PIN
Figure 2-5
ALIGNING TERMINAL
PINS TO HOLES
CONNECTOR
ASSEMBLY
SUPPORT PALLET
Figure 2-6
CONNECTOR ASSEMBLY
Backplane Signal Module Insertion Tooling
ON PC BOARD SUPPORT PALLET
1. Carefully pre-seat, by hand, the backplane signal module(s) into the printed circuit board hole pattern. Make
sure the connector(s) are oriented properly by confirming the location of the #1 circuit notch with respect to
the printed circuit board layout. See Figure 2-5.
2. Locate the pre-loaded board into the support pallet (Optional). See Figure 2-6.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 8 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| ABMM-14.7456MHZ-B2-T | CRYSTAL 14.7456MHZ 18PF SMD |
| B32520C3103K189 | FILM CAP 0.0100UF 10% 250V |
| 1624146-2 | POT 470K OHM 0.4W 20% SIDE FLAT |
| 1624144-2 | POT 47K OHM 0.4W 20% SIDE FLAT |
| ASA1-3.6864MHZ-L-T | OSC 3.6864 MHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621005200 | 功能描述:MICRO TCA REMOVAL TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0621005300 | 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL - Bulk |
| 0621005400 | 制造商:Molex 功能描述:CONNECTOR SYSTEM TERMINAL REMOVAL TOOL 制造商:Molex 功能描述:TERMINAL REMOVAL TOOL - Bulk |
| 0621005700 | 功能描述:AMC B+ REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0621005800 | 功能描述:IMPACT REPAIR TOOL - BACKPLANE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。