- 您现在的位置：买卖IC网 > PDF目录18521 > 0621005110 (Molex Inc)TOOL INSERT SIGNAL CONTACT PDF资料下载
参数资料
| 型号： | 0621005110 |
| 厂商： | Molex Inc |
| 文件页数： | 15/27页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT SIGNAL CONTACT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-5110 62100-5110 621005110 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
3.1. Cleaning
Once a day, the support fixture should be cleaned of dust and plating particles and other debris. Compressed air
may be necessary to remove debris from the pin clearance holes.
CAUTION: Use extreme caution when using compressed air for cleaning, it can cause debris to get
lodged in the tooling or come flying out at the operator. USE of proper safety glasses by the operator and
onlookers is required.
3.2 Lubrication
There is no lubrication required on any of the I-Trac? tooling. However, the presses each have their own
requirements for lubrication and maintenance. The instruction manual for the specific press being used should be
referred to. Molex provides a sheet for logging routine preventive maintenance in this section.
3.3 Troubleshooting
Symptom
Connector
being damaged
Cause
Press stroke set to low.
Connector and/or tooling not properly aligned
"Blades" on tooling bent or damaged
Solution
Refer to the appropriate press manual
and adjust the stroke. See Section 2.2
Check Fixture and Repair as required.
Check alignment of fixture in press
Check to be sure the press platen is
pressing squarely on the tooling block.
Replace tool.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 15 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| ABMM-14.7456MHZ-B2-T | CRYSTAL 14.7456MHZ 18PF SMD |
| B32520C3103K189 | FILM CAP 0.0100UF 10% 250V |
| 1624146-2 | POT 470K OHM 0.4W 20% SIDE FLAT |
| 1624144-2 | POT 47K OHM 0.4W 20% SIDE FLAT |
| ASA1-3.6864MHZ-L-T | OSC 3.6864 MHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621005200 | 功能描述:MICRO TCA REMOVAL TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0621005300 | 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL - Bulk |
| 0621005400 | 制造商:Molex 功能描述:CONNECTOR SYSTEM TERMINAL REMOVAL TOOL 制造商:Molex 功能描述:TERMINAL REMOVAL TOOL - Bulk |
| 0621005700 | 功能描述:AMC B+ REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0621005800 | 功能描述:IMPACT REPAIR TOOL - BACKPLANE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。