- 您现在的位置：买卖IC网 > PDF目录18521 > 0621005110 (Molex Inc)TOOL INSERT SIGNAL CONTACT PDF资料下载
参数资料
| 型号： | 0621005110 |
| 厂商： | Molex Inc |
| 文件页数： | 24/27页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT SIGNAL CONTACT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-5110 62100-5110 621005110 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
5.1 I-Trac? Backplane Repair Procedure:
For the removal and replacement of Signal Pair pins.
The following tools are required:
Signal Pin Replacement Tool 62100-5110
Needle nose pliers (miniature) *
Tweezers *
* Not supplied by Molex
Removal
To remove damaged signal pins, grasp them with the needle nose
pliers and pull straight up from the board. See Figure 5-1. In
NEEDLE
NOSE
PLIERS
CONNECTOR
FIGURE 5-1
SIGNAL PINS
some cases it may be necessary to straighten a bent pin with the tweezers to allow access with the pliers.
NOTE: Never reuse a backplane signal pin once it has been removed. In addition, no more than three pins
should be pressed into any plated through hole. Replacement pins should be removed from a spare virgin
connector.
Replacement
1. Place the replacement signal contact at the tip of the insertion tool and slide the contact so it rests underneath
the terminal clamp. See Figure 5-2.
TERMINAL
CLAMP
INSERTION
TOOL
REPLACED
CONTACT
SIGNAL
HOUSING
PCB
CONTACTS SHOULDER IS
CONTACT
SIGNAL
CONTACT
FLUSH AGAINST TOOL TIP
Figure 5-2
Figure 5-3
ADJACENT ROW
2. The signal contact will be guided using the groove located on the insertion tool and should be pushed all the
way underneath the terminal clamp.
3. The signal contact is completely seated in the insertion tool when, the contacts shoulder is resting against the
insertion tool tip and can no longer be moved up.
4. Make sure the signal contact is in the correct orientation. Check the column where the repair signal contact is
being replaced and compare the column to the contact signal on the insertion tool. The two should be the
same. The adjacent column is oriented in the opposite direction. See Figure 5-3.
5. Line-up the pins tip on the signal contact, with the hole in the signal module and push the pin tip with the
insertion tool through the housing and the PRINTED CIRCUIT BOARD.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 24 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| ABMM-14.7456MHZ-B2-T | CRYSTAL 14.7456MHZ 18PF SMD |
| B32520C3103K189 | FILM CAP 0.0100UF 10% 250V |
| 1624146-2 | POT 470K OHM 0.4W 20% SIDE FLAT |
| 1624144-2 | POT 47K OHM 0.4W 20% SIDE FLAT |
| ASA1-3.6864MHZ-L-T | OSC 3.6864 MHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621005200 | 功能描述:MICRO TCA REMOVAL TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0621005300 | 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL - Bulk |
| 0621005400 | 制造商:Molex 功能描述:CONNECTOR SYSTEM TERMINAL REMOVAL TOOL 制造商:Molex 功能描述:TERMINAL REMOVAL TOOL - Bulk |
| 0621005700 | 功能描述:AMC B+ REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0621005800 | 功能描述:IMPACT REPAIR TOOL - BACKPLANE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。