- 您现在的位置：买卖IC网 > PDF目录18521 > 0621005110 (Molex Inc)TOOL INSERT SIGNAL CONTACT PDF资料下载
参数资料
| 型号： | 0621005110 |
| 厂商： | Molex Inc |
| 文件页数： | 22/27页 |
| 文件大小： | 0K |
| 描述： | TOOL INSERT SIGNAL CONTACT |
| 标准包装： | 1 |
| 系列： | * |
| 其它名称： | 062100-5110 62100-5110 621005110 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页当前第22页第23页第24页第25页第26页第27页
I-Trac? Backplane and Daughtercard Tooling
4.1 Standard Tool Ordering Procedure
Stacking Tooling
All the insertion tooling listed in Table 4-1 and 4-2 can be stacked in any
combination to be able to simultaneously press in any arrangement of
stacked connectors. Tooling holders are available in various lengths.
Figure 4-1 shows a typical setup for an 11 row by 8 column backplane
signal module in a standard tool holder.
Ordering Tooling for Backplane Connectors
In order to insert a typical row of backplane connectors, it is necessary to
Figure 4-1
TYPICAL INSERTION
TOOL ASSEMBLY
select the individual insertion tools and then pick the appropriate tooling holder (See example).
Basic Procedure
CAUTION : Vertical Power Module must be installed separately without any Backplane or DaughterCard
assemblies in the combinations.
1. Determine the combination of signal modules to be inserted.
2. Select the proper press-in tools from Table 4-1 and Table 4-2.
3. Table 4-1 and Table 4-2 show the tool sizes. (L) Write down the length of each tool selected.
NOTE: Make sure that if you require four of a particular tool, write down its length 4 times.
4. Total up these lengths.
5. Using the length just calculated, select the next largest tooling holder from Table 4-3. The tooling holder can
be shorter than the total tooling but not by more than 0.5 mm per side.
6. All of the tools selected above must be ordered separately.
Example
To be inserted: (1) 5 row by 5 column and (1) 11 row by 8 column Backplane Signal Module.
1. Look at Table 4-1 and find the required tools. In this case it would be a 62201-8613 and 62201-8617.
2. From Table 4-1 get the lengths of these tools. (Numbers may be rounded up) 62201-8613=18.5mm and
62201-8617=29.6mm.
3. Add these values totaling of 48.1mm, round up (49.0mm).
4. From the Tooling Holder list in Table 4-3, pick the 72.0mm long holder, part number 62201-9502.
5. Thus the order to Molex should include the following:
Quantity
1
1
1
Order No.
62201-8613
62201-8617
62201-9502
Description
5 row by 5 column Backplane Signal Module Press-In Tool
11 row by 8 column Backplane Signal Module Press-In Tool
72.0mm Long Tooling Holder
Ordering Daughtercard Tooling
Daughtercard connectors only come in standard module sizes. The Daughtercard insertion modules lengths are
based on the module size. Therefore, insertion tools can be used individually for a connector assembly or stacked in
a tool holder for multiple connector assemblies. Select the specific tool for your connector from Table 4-3.
Doc. No: TM-622018699
Revision: D
Release Date: 12-05-07
Revision Date: 04-15-10
UNCONTROLLED COPY
Page 22 of 27
相关PDF资料 |
PDF描述 |
|---|---|
| ABMM-14.7456MHZ-B2-T | CRYSTAL 14.7456MHZ 18PF SMD |
| B32520C3103K189 | FILM CAP 0.0100UF 10% 250V |
| 1624146-2 | POT 470K OHM 0.4W 20% SIDE FLAT |
| 1624144-2 | POT 47K OHM 0.4W 20% SIDE FLAT |
| ASA1-3.6864MHZ-L-T | OSC 3.6864 MHZ 2.5V SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 0621005200 | 功能描述:MICRO TCA REMOVAL TOOL RoHS:否 类别:工具 >> 压接器，施用器，压力机 - 配件 系列:* 标准包装:1 系列:- 其它名称:512A512A-NDQ1137690B |
| 0621005300 | 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL 制造商:Molex 功能描述:Z-POWER EXTRACTION TOOL - Bulk |
| 0621005400 | 制造商:Molex 功能描述:CONNECTOR SYSTEM TERMINAL REMOVAL TOOL 制造商:Molex 功能描述:TERMINAL REMOVAL TOOL - Bulk |
| 0621005700 | 功能描述:AMC B+ REMOVAL TOOL RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
| 0621005800 | 功能描述:IMPACT REPAIR TOOL - BACKPLANE RoHS:否 类别:工具 >> 插入，抽取 系列:* 标准包装:1 系列:* 其它名称:0011-03-00080011-03-0008-E00110300080011030008-E11-03-0008-E1103000811030008-EQ4729393AT0980176A |
发布紧急采购，3分钟左右您将得到回复。