- 您现在的位置：买卖IC网 > PDF目录18714 > 4460-TCE10D434-EK (Silicon Laboratories Inc)KIT EZRADIO TEST CARD SI4460 TX PDF资料下载
参数资料
| 型号： | 4460-TCE10D434-EK |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 26/56页 |
| 文件大小： | 0K |
| 描述： | KIT EZRADIO TEST CARD SI4460 TX |
| 设计资源： | 4460-TCE10D434 BOM 4460-TCE10D434 PCB 4460-TCE10D434 SCH |
| 标准包装： | 1 |
| 系列： | EZRadioPRO® |
| 类型： | 收发器，ISM |
| 频率： | 434MHz |
| 适用于相关产品： | Si4460 |
| 已供物品： | 板 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页
Si4464/63/61/60
4.2. Modulation Types
The Si446x supports five different modulation options: Gaussian frequency shift keying (GFSK), frequency-shift
keying (FSK), four-level GFSK (4GFSK), four-level FSK (4FSK), and on-off keying (OOK). Minimum shift keying
(MSK) can also be created by using GFSK settings. GFSK is the recommended modulation type as it provides the
best performance and cleanest modulation spectrum. The modulation type is set by the “MOD_TYPE[2:0]”
registers in the “MODEM_MOD_TYPE” API property. A continuous-wave (CW) carrier may also be selected for RF
evaluation purposes. The modulation source may also be selected to be a pseudo-random source for evaluation
purposes.
4.3. Hardware Configuration Options
There are different receive demodulator options to optimize the performance and mutually-exclusive options for
how the RX/TX data is transferred from the host MCU to the RF device.
4.3.1. Receive Demodulator Options
There are multiple demodulators integrated into the device to optimize the performance for different applications,
modulation formats, and packet structures. The calculator built into WDS will choose the optimal demodulator
based on the input criteria.
4.3.1.1. Synchronous Demodulator
The synchronous demodulator's internal frequency error estimator acquires the frequency error based on a
101010 preamble structure. The bit clock recovery circuit locks to the incoming data stream within four transactions
of a “10” or “01” bit stream. The synchronous demodulator gives optimal performance for 2- or 4-level FSK or
GFSK modulation that has a modulation index less than 2.
4.3.1.2. Asynchronous Demodulator
The asynchronous demodulator should be used OOK modulation and for FSK/GFSK/4GFSK under one or more of
the following conditions:
?? Modulation
index > 2
?? Non-standard preamble (not 1010101... pattern)
When the modulation index exceeds 2, the asynchronous demodulator has better sensitivity compared to the
synchronous demodulator. An internal deglitch circuit provides a glitch-free data output and a data clock signal to
simplify the interface to the host. There is no requirement to perform deglitching in the host MCU. The
asynchronous demodulator will typically be utilized for legacy systems and will have many performance benefits
over devices used in legacy designs. Unlike the Si4432/31 solution for non-standard packet structures, there is no
requirement to perform deglitching on the data in the host MCU. Glitch-free data is output from Si446x devices, and
a sample clock for the asynchronous data can also be supplied to the host MCU; so, oversampling or bit clock
recovery is not required by the host MCU. There are multiple detector options in the asynchronous demodulator
block, which will be selected based upon the options entered into the WDS calculator. The asynchronous
demodulator's internal frequency error estimator is able to acquire the frequency error based on any preamble
structure.
4.3.2. RX/TX Data Interface With MCU
There are two different options for transferring the data from the RF device to the host MCU. FIFO mode uses the
SPI interface to transfer the data, while direct mode transfers the data in real time over GPIO.
4.3.2.1. FIFO Mode
In FIFO mode, the transmit and receive data is stored in integrated FIFO register memory. The TX FIFO is
accessed by writing Command 66h followed directly by the data/clk that the host wants to write into the TX FIFO.
The RX FIFO is accessed by writing command 77h followed by the number of clock cycles of data the host would
like to read out of the RX FIFO. The RX data will be clocked out onto the SDO pin.
In TX mode, if the packet handler is enabled, the data bytes stored in FIFO memory are “packaged” together with
other fields and bytes of information to construct the final transmit packet structure. These other potential fields
include the Preamble, Sync word, Header, CRC checksum, etc. The configuration of the packet structure in TX
mode is determined by the Automatic Packet Handler (if enabled), in conjunction with a variety of Packet Handler
properties. If the Automatic Packet Handler is disabled, the entire desired packet structure should be loaded into
FIFO memory; no other fields (such as Preamble or Sync word) will be automatically added to the bytes stored in
26
Rev 1.2
相关PDF资料 |
PDF描述 |
|---|---|
| SI4844-DEMO | SI4844 EVAL AND DEMO BOARD |
| GSEB01D | SWITCH ROTARY SIDE |
| ATAKSTK511-8 | KIT RF MODULE 868MHZ FOR STK500 |
| XT09-DK | KIT DEVELOPMENT 900MHZ |
| ATAKSTK511-9 | KIT RF MODULE 915MHZ FOR STK500 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 4460-TCE10D868-EK | 功能描述:射频开发工具 4460 10 dBm 868MHz Test Card RoHS:否 制造商:Taiyo Yuden 产品:Wireless Modules 类型:Wireless Audio 工具用于评估:WYSAAVDX7 频率: 工作电源电压:3.4 V to 5.5 V |
| 446-0X | 制造商:Apex Tool Group 功能描述:HEX BIT PHILLIPS #0X25MM TOOL STEEL 制造商:APEX 功能描述:HEX BIT, PHILLIPS, #0X25MM, TOOL STEEL 制造商:APEX 功能描述:HEX BIT, PHILLIPS, #0X25MM, TOOL STEEL; Bit Type:Phillips; Hex Bit Size:#0; Length:25mm; Size:1" ;RoHS Compliant: NA |
| 4461 | 功能描述:电缆固定件和配件 PG16 HYBRID CG 1.48X1.10 .39-.67 RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| 44-610 | 制造商:RAWLPLUG 功能描述:RAWLBOLT PROJECTING M1030P 制造商:RAWLPLUG 功能描述:RAWLBOLT, PROJECTING, M1030P |
| 44610 | 制造商:3-IN-ONE 功能描述:3IN1 SILICONE SPRAY, 400ML |
发布紧急采购，3分钟左右您将得到回复。