- 您现在的位置：买卖IC网 > Datasheet目录601 > 58558-1 (TE Connectivity)CONSUMER BNC TOOL RG 58/59 Datasheet资料下载
参数资料
| 型号： | 58558-1 |
| 厂商： | TE Connectivity |
| 文件页数： | 4/5页 |
| 文件大小： | 0K |
| 描述： | CONSUMER BNC TOOL RG 58/59 |
| 标准包装： | 5 |
| 系列： | Pro-Crimper III |
| 工具类型： | 手动压接器 |
| 适用于相关产品： | 同轴，RF - BNC |
| 特点： | 侧面插入，棘齿 |
5. Remove and inspect the center contact.
6. Make another sample crimp. If the contact is still
being bent during crimping, repeat the adjustment
procedure.
The frame assembly ratchet mechanism features an
adjustment wheel with numbered settings. If the crimp
height or retention force is not acceptable, adjust the
ratchet as follows:
1. Remove the lockscrew from the ratchet
adjustment wheel.
Figure 4
4. While holding the assembly together, begin to
close the tool handles. Keep holding the assembly
until the dies have closed enough to hold the
assembly in place.
5. Carefully close the tool handles until the ratchet
releases.
6. Allow the tool handles to open fully and remove
the crimped connector from the dies.
Make a sample crimp and determine if the center
contact is bending upward, bending downward, or
bending from side to side. If the contact is bent,
adjustment is required.
1. Loosen the adjustment screw.
2. Place a center contact with cable into the proper
crimping chamber and close the tool handles until
the locator and straightener assembly is holding
the contact in position.
3. Move the straightener up or down, as required,
to eliminate the bending of the center contact.
4. Tighten the adjustment screw and close the
handles until the ratchet releases.
2. With a screwdriver, adjust the ratchet wheel
from the opposite side of the frame.
3. Observe the ratchet adjustment wheel. If a
tighter crimp is required, rotate the adjustment
wheel COUNTERCLOCKWISE to a
higher–numbered setting. If a looser crimp is
required, rotate the adjustment wheel
CLOCKWISE to a lower–numbered setting.
4. Replace the lockscrew.
5. Make a sample crimp and measure the crimp
height. If the crimp height is acceptable, secure the
lockscrew. If the dimension is unacceptable,
remove lockscrew and continue to adjust the
ratchet, and again measure a sample crimp.
Figure 5
相关PDF资料 |
PDF描述 |
|---|---|
| 58560-1 | TOOL CRIMP MODULAR 10 POS W/DIE |
| 58605-2 | PROCRIMP DIE JPT W/SEAL |
| 58638-1 | TOOL TERM HEAD MTA .100 PIN |
| 58644-1 | TOOL HEAD MTA .100 MASS INSERT |
| 58646-1 | TOOL HEAD MTA .156 MASS INSERT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 58558-2 | 功能描述:冲压机与冲模 CONSUMER BNC DIE SET RG 58/59 RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 58559-1 | 功能描述:手工工具 CONSUMER BNC TOOL RG 174/179 RoHS:否 制造商:Molex 产品:Extraction Tools 类型: 描述/功能:Extraction tool |
| 58559-2 | 功能描述:冲压机与冲模 CONSUMER BNC DIE SET RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 5855B | 制造商:DISSTON 功能描述:HOLE SAW VARIPITCH HSS 14MM |
| 5855-BL005 | 制造商:Alpha Wire Company 功能描述:Hook-up Wire 1Conductors 22AWG 30.5m 1.3mm Silver Plated Copper Blue 600V |
发布紧急采购，3分钟左右您将得到回复。