参数资料
型号: 71M6521FE-IGT/F
厂商: MAXIM INTEGRATED PRODUCTS INC
元件分类: 模拟信号调理
英文描述: SPECIALTY ANALOG CIRCUIT, QFP64
封装: LEAD FREE, LQFP-64
文件页数: 25/103页
文件大小: 1691K
代理商: 71M6521FE-IGT/F
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
Page: 28 of 103
2005-2010 Teridian Semiconductor Corporation
v1.1
A Maxim Integrated Products Brand
19-5370; 10/10
Table 24 specifies the combinations of operation modes allowed for timer 0 and timer 1:
Timer 1
Mode 0
Mode 1
Mode 2
Timer 0 - mode 0
YES
Timer 0 - mode 1
YES
Timer 0 - mode 2
Not allowed
YES
Table 24: Timer Modes
Timer/Counter Mode Control register (PCON):
MSB
LSB
SMOD
--
Table 25: The PCON Register
The SMOD bit in the PCON register doubles the baud rate when set.
Bit
Symbol
Function
PCON.7
SMOD
Baud rate control.
Table 26: PCON Register Bit Description
WD Timer (Software Watchdog Timer)
The software watchdog timer is a 16-bit counter that is incremented once every 24 or 384 clock cycles. After a reset, the
watchdog timer is disabled and all registers are set to zero. The watchdog consists of a 16-bit counter (WDT), a reload register
(WDTREL), prescalers (by 2 and by 16), and control logic. Once the watchdog is started, it cannot be stopped unless the
internal reset signal becomes active.
Note: It is recommended to use the hardware watchdog timer instead of the software watchdog timer.
WD Timer Start Procedure: The WDT is started by setting the SWDT flag. When the WDT register enters the state 0x7CFF,
an asynchronous WDTS signal will become active. The signal WDTS sets bit 6 in the IP0 register and requests a reset state.
WDTS is cleared either by the reset signal or by changing the state of the WDT timer.
Refreshing the WD Timer: The watchdog timer must be refreshed regularly to prevent the reset request signal from becoming
active. This requirement imposes an obligation on the programmer to issue two instructions. The first instruction sets WDT and
the second instruction sets SWDT. The maximum delay allowed between setting WDT and SWDT is 12 clock cycles. If this
period has expired and SWDT has not been set, the WDT is automatically reset, otherwise the watchdog timer is reloaded with
the content of the WDTREL register and the WDT is automatically reset. Since the WDT requires exact timing, firmware needs
to be designed with special care in order to avoid unwanted WDT resets. Teridian strongly discourages the use of the
software WDT.
相关PDF资料
PDF描述
71M6531D-IMR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68
71M6532D-IGTR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100
71M6532F-IGT/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100
71M6531D-IM/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68
71M6531F-IMR/F 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68
相关代理商/技术参数
参数描述
71M6521FE-IGTR 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC
71M6521FE-IGTR/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6521FE-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6521FE-IM 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC
71M6521FE-IM/F 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel