- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6521FE-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, QFP64 PDF资料下载
参数资料
| 型号： | 71M6521FE-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, QFP64 |
| 封装： | LEAD FREE, LQFP-64 |
| 文件页数： | 37/103页 |
| 文件大小： | 1691K |
| 代理商： | 71M6521FE-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页
71M6521DE/71M6521FE
Energy Meter IC
DATA SHEET
OCTOBER 2010
v1.1
2005-2010 Teridian Semiconductor Corporation
Page: 39 of 103
A Maxim Integrated Products Brand
19-5370; 10/10
Physical Memory
Flash Memory: The 71M6521DE/FE includes 16KB (71M6521DE) or 32KB (71M6521FE) of on-chip flash memory. The flash
memory primarily contains MPU and CE program code. It also contains images of the CE DRAM, MPU RAM, and I/O RAM.
On power-up, before enabling the CE, the MPU copies these images to their respective locations.
Allocated flash space for the CE program cannot exceed 1024 words (2KB). The CE program must begin on a 1KB boundary
of the flash address. The CE_LCTN[4:0] word defines which 1KB boundary contains the CE code.
Thus, the first CE
instruction is located at 1024*CE_LCTN[4:0]. CE_LCTN must be defined before the CE is enabled.
The flash memory is segmented into 512 byte individually erasable pages.
The CE engine cannot access its program memory when flash write occurs. Thus, the flash write procedure is to begin a
sequence of flash writes when CE_BUSY falls (CE_BUSY interrupt) and to make sure there is sufficient time to complete the
sequence before CE_BUSY rises again. The actual time for the flash write operation will depend on the exact number of cycles
required by the CE program. Typically (CE program is 512 instructions, mux frame is 13 CK32 cycles), there will be 200s of
flash write time, enough for 4 bytes of flash write. If the CE code is shorter, there will be even more time.
Two interrupts warn of collisions between the MPU firmware and the CE timing. If a flash write is attempted while the CE is
busy, the flash write will not execute and the FW_COL0 interrupt will be issued. If a flash write is still in progress when the CE
would otherwise begin a code pass, the code pass is skipped, the write is completed, and the FW_COL1 interrupt is issued.
The bit FLASH66Z (see I/O RAM table) defines the speed for accessing flash memory. To minimize supply current draw, this bit
should be set to 1.
Flash erasure is initiated by writing a specific data pattern to specific SFR registers in the proper sequence. These special
pattern/sequence requirements prevent inadvertent erasure of the flash memory.
The mass erase sequence is:
1.
Write 1 to the FLSH_MEEN bit (SFR address 0xB2[1].
2.
Write pattern 0xAA to FLSH_ERASE (SFR address 0x94)
The mass erase cycle can only be initiated when the ICE port is enabled.
The page erase sequence is:
1.
Write the page address to FLSH_PGADR (SFR address 0xB7[7:1]
2.
Write pattern 0x55 to FLSH_ERASE (SFR address 0x94)
The MPU may write to the flash memory. This is one of the non-volatile storage options available to the user in addition to
external EEPROM.
FLSH_PWE (flash program write enable) differentiates 80515 data store instructions (MOVX@DPTR,A) between flash and
XRAM writes.
Updating individual bytes in flash memory:
The original state of a flash byte is 0xFF (all ones). Once, a value other than 0xFF is written to a flash memory cell, overwriting
with a different value usually requires that the cell is erased first. Since cells cannot be erased individually, the page has to be
copied to RAM, followed by a page erase. After this, the page can be updated in RAM and then written back to the flash
memory.
MPU RAM: The 71M6521DE/FE includes 2k-bytes of static RAM memory on-chip (XRAM) plus 256-bytes of internal RAM in
the MPU core. The 2K-bytes of static RAM are used for data storage during normal MPU operations.
CE DRAM: The CE DRAM is the working data memory of the CE (128 32-bit words). The MPU can read and write the CE
DRAM as the primary means of data communication between the two processors.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6531D-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6532D-IGTR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6532F-IGT/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PQFP100 |
| 71M6531D-IM/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
| 71M6531F-IMR/F | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, QCC68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6521FE-IGTR | 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC |
| 71M6521FE-IGTR/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521FE-IGTR/F1 | 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6521FE-IM | 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Energy Meter IC |
| 71M6521FE-IM/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。