- 您现在的位置：买卖IC网 > PDF目录20616 > 71M6521FE-IMR/F (Maxim Integrated)IC ENERGY METER 32K FLASH 68-QFN PDF资料下载
参数资料
| 型号： | 71M6521FE-IMR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 38/107页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 32K FLASH 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Single Converter Technology® |
| 测量误差： | 0.4% |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相，双相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（7.5x7.5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页当前第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页
71M6521DE/DH/FE Data Sheet
On-Chip Resources
Oscillator
The 71M6521DE/DH/FE oscillator drives a standard 32.768kHz watch crystal. These crystals are accurate and do not
require a high-current oscillator circuit. The 71M6521DE/DH/FE oscillator has been designed specifically to handle
these crystals and is compatible with their high impedance and limited power handling capability.
PLL and Internal Clocks
Timing for the device is derived from the 32.768kHz oscillator output. On-chip timing functions include the MPU
master clock, a real time clock (RTC), and the delta-sigma sample clock. In addition, the MPU has two general
counter/timers (see MPU section).
The ADC master clock, CKADC, is generated by an on-chip PLL. It multiplies the oscillator output frequency (CK32)
by 150.
The CE clock frequency is always CK32 * 150, or 4.9152MHz, where CK32 is the 32kHz clock. The MPU clock
frequency is determined by MPU_DIV and can be 4.9152MHz *2 - MPU_DIV Hz where MPU_DIV varies from 0 to 7
( MPU_DIV is 0 on power-up). This makes the MPU clock scalable from 4.9152MHz down to 38.4kHz. The circuit also
generates a 2x MPU clock for use by the emulator. This clock is not generated when ECK_DIS is asserted by the
MPU.
The setting of MPU_DIV is maintained when the device transitions to BROWNOUT mode, but the time base in
BROWNOUT mode is 28,672Hz.
Real-Time Clock (RTC)
The RTC is driven directly by the crystal oscillator. It is powered by the net V2P5NV (battery-backed up supply). The
RTC consists of a counter chain and output registers. The counter chain consists of seconds, minutes, hours, day of
week, day of month, month, and year. The RTC is capable of processing leap years. Each counter has its own output
register. Whenever the MPU reads the seconds register, all other output registers are automatically updated. Since
the RTC clock is not coherent to the MPU clock, the MPU must read the seconds register until two consecutive reads
are the same (requires either 2 or 3 reads). At this point, all RTC output registers will have the correct time.
Regardless of the MPU clock speed, RTC reads require one wait state.
RTC time is set by writing to the RTC registers in I/O RAM. Each byte written to RTC must be delayed at least 3 RTC
cycles from any previous byte written to RTC. Hardware RTC write protection requires that a write to address 0x201F
occur before each RTC write. Writing to address 0x201F opens a hardware ‘enable gate’ that remains open until an
RTC write occurs and then closes. It is not necessary to disable interrupts between the write operation to 0x201F and
the RTC write because the ‘enable gate’ will remain open until the RTC write finally occurs
Two time correction bits, RTC_DEC_SEC and RTC_INC_SEC are provided to adjust the RTC time. A pulse on one of
these bits causes the time to be decremented or incremented by an additional second at the next update of the
RTC_SEC register. Thus, if the crystal temperature coefficient is known, the MPU firmware can integrate temperature
and correct the RTC time as necessary.
Temperature Sensor
The device includes an on-chip temperature sensor for determining the temperature of the bandgap reference. The
MPU may request an alternate multiplexer frame containing the temperature sensor output by asserting MUX_ALT .
The primary use of the temperature data is to determine the magnitude of compensation required to offset the
thermal drift in the system (see section titled “Temperature Compensation”).
Page: 38 of 107
Rev 3
相关PDF资料 |
PDF描述 |
|---|---|
| A7PPB-1506M | CABLE D-SUB-AMM15B/AE15M/AMM15B |
| VI-BNP-EU-F2 | CONVERTER MOD DC/DC 13.8V 200W |
| ADP194ACBZ-R7 | IC POWER SWITCH HS LOGIC 4WLSCP |
| 591D336X9016R2T15H | CAP TANT 33UF 16V 10% 2824 |
| 71M6521FE-IGTR/F | IC ENERGY METER 32K FLASH 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6521-TGP1-68M | 制造商:Maxim Integrated Products 功能描述:Programmer Accessories Gang Programmer Base w/6521 Socket Brd |
| 71M6523-DB | 功能描述:开发板和工具包 - 8051 71M6521D Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6523-IM | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6523-IM/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6523-IMR | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。