- 您现在的位置：买卖IC网 > PDF目录20616 > 71M6521FE-IMR/F (Maxim Integrated)IC ENERGY METER 32K FLASH 68-QFN PDF资料下载
参数资料
| 型号： | 71M6521FE-IMR/F |
| 厂商： | Maxim Integrated |
| 文件页数： | 46/107页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 32K FLASH 68-QFN |
| 产品培训模块： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 标准包装： | 2,500 |
| 系列： | Single Converter Technology® |
| 测量误差： | 0.4% |
| 电源电压： | 3 V ~ 3.6 V |
| 测量仪表类型： | 单相，双相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘 |
| 供应商设备封装： | 64-QFN（7.5x7.5） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页当前第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页
71M6521DE/DH/FE Data Sheet
Hardware Watchdog Timer
V3P3
V3P3 - 10mV
V3P3 -
400mV
VBIAS
V1
WDT dis-
abled
Normal
operation,
WDT
enabled
Battery
modes
In addition to the basic watchdog timer included in the 80515 MPU, an
independent, robust, fixed-duration, watchdog timer (WDT) is included in the
device. It uses the RTC crystal oscillator as its time base and must be refreshed
by the MPU firmware at least every 1.5 seconds. When not refreshed on time the
WDT overflows, and the part is reset as if the RESET pin were pulled high, except
that the I/O RAM bits will be in the same state as after a wake-up from SLEEP or
LCD modes (see the I/O RAM description for a list of I/O RAM bit states after
RESET and wake-up). 4100 oscillator cycles (or 125ms) after the WDT overflow,
the MPU will be launched from program address 0x0000.
A status bit, WD_OVF , is set when WDT overflow occurs. This bit is powered by
the non-volatile supply and can be read by the MPU to determine if the part is
initializing after a WDT overflow event or after a power-up. After it is read, MPU
firmware must clear WD_OVF . The WD_OVF bit is cleared by the RESET pin
There is no internal digital state that deactivates the WDT. For debug purposes,
Of course, this also deactivates V1 power fault detection. Since there is no
method in firmware to disable the crystal oscillator or the WDT, it is guaranteed
that whatever state the part might find itself in, upon WDT overflow, the part will
be reset to a known state.
disable the WDT in BROWNOUT mode.
Asserting ICE_E will also deactivate the WDT. This is the only method that will
0V
In normal operation, the WDT is reset by periodically writing a one to the
WDT_RST bit. The watchdog timer is also reset when the internal signal WAKE=0 (see section on Wake Up Behavior).
Figure 14: Functions defined by V1
Program Security
When enabled, the security feature limits the ICE to global flash erase operations only. All other ICE operations are
blocked. This guarantees the security of the user’s MPU and CE program code. Security is enabled by MPU code
that is executed in a 32 cycle preboot interval before the primary boot sequence begins. Once security is enabled, the
only way to disable it is to perform a global erase of the flash, followed by a chip reset.
The first 32 cycles of the MPU boot code are called the preboot phase because during this phase the ICE is inhibited.
A read-only status bit, PREBOOT , identifies these cycles to the MPU. Upon completion of preboot, the ICE can be
enabled and is permitted to take control of the MPU.
SECURE , the security enable bit, is reset whenever the chip is reset. Hardware associated with the bit permits only
ones to be written to it. Thus, preboot code may set SECURE to enable the security feature but may not reset it. Once
SECURE is set, the preboot code is protected and no external read of program code is possible
Specifically, when SECURE is set:
?
?
?
The ICE is limited to bulk flash erase only.
Page zero of flash memory, the preferred location for the user’s preboot code, may not be page-erased by
either MPU or ICE. Page zero may only be erased with global flash erase.
Writes to page zero, whether by MPU or ICE are inhibited.
The SECURE bit is to be used with caution! Inadvertently setting this bit will inhibit access to the part via
the ICE interface, if no mechanism for actively resetting the part between reset and erase operations is
provided (see ICE Interface description).
Page: 46 of 107
Rev 3
相关PDF资料 |
PDF描述 |
|---|---|
| A7PPB-1506M | CABLE D-SUB-AMM15B/AE15M/AMM15B |
| VI-BNP-EU-F2 | CONVERTER MOD DC/DC 13.8V 200W |
| ADP194ACBZ-R7 | IC POWER SWITCH HS LOGIC 4WLSCP |
| 591D336X9016R2T15H | CAP TANT 33UF 16V 10% 2824 |
| 71M6521FE-IGTR/F | IC ENERGY METER 32K FLASH 64LQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6521-TGP1-68M | 制造商:Maxim Integrated Products 功能描述:Programmer Accessories Gang Programmer Base w/6521 Socket Brd |
| 71M6523-DB | 功能描述:开发板和工具包 - 8051 71M6521D Demo Brd RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
| 71M6523-IM | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6523-IM/F | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6523-IMR | 功能描述:计量片上系统 - SoC Residential Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。