- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6543F-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6543F-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 100/157页 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页当前第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
71M6543F/H and 71M6543G/GH Data Sheet
v1.2
2008–2011 Teridian Semiconductor Corporation
47
2.5
On-Chip Resources
2.5.1
Physical Memory
2.5.1.1 Flash Memory
The device includes 64 KB (71M6543F/H) or 128 KB (71M6543G/GH) of on-chip flash memory. The
flash memory primarily contains MPU and CE program code. It also contains images of the CE RAM and
I/O RAM. On power-up, before enabling the CE, the MPU copies these images to their respective
locations.
Flash space allocated for the CE program is limited to 4096 16-bit words (8 KB). The CE program must
begin on a 1-KB boundary of the flash address space. The CE_LCTN[6/5:0] (I/O RAM 0x2109[5:0]) field
on the 71M6543F/H and the CE_LCTN[6:0] (I/O RAM 0x2109[6:0]) field on the 71M6543G/GH define
which 1-KB boundary contains the CE code. Thus, the first CE instruction is located at
1024*CE_LCTN[6/5:0] on the 71M6543F/H and at 1024*CE_LCTN[6:0] on the 71M6543G/GH.
Flash memory can be accessed by the MPU, the CE, and by the SPI interface (R/W).
Table 39: Flash Memory Access
Access by
Access
Type
Condition
MPU
R/W/E
W/E only if CE is disabled.
CE
R
SPI
R/W/E
Access only when SFM is invoked (MPU halted).
Flash Write Procedures
If the FLSH_UNLOCK[3:0] (I/O RAM 0x2702[7:4]) key is correctly programmed, the MPU may write to the
flash memory. This is one of the non-volatile storage options available to the user in addition to external
EEPROM.
The flash program write enable bit, FLSH_PSTWR (SFR 0xB2[0]), differentiates 80515 data store instructions
(MOVX@DPTR,A) between Flash and XRAM writes. This bit is automatically cleared by hardware after
each byte write operation. Write operations to this bit are inhibited when interrupts are enabled.
If the CE is enabled (CE_E = 1, I/O RAM 0x2106[0]), flash write operations must not be attempted unless
FLSH_PSTWR is set. This bit enables the “posted flash write” capability. FLSH_PSTWR has no effect when
CE_E = 0). When CE_E = 1, however, FLSH_PSTWR delays a flash write until the time interval between
the CE code passes. During this delay time, the FLSH_PEND (SFR 0xB2[3]) bit is high, and the MPU
continues to execute commands. When the CE code pass ends (CE_BUSY falls), the FLSH_PEND bit
falls and the write operation occurs. The MPU can query the FLSH_PEND bit to determine when the
write operation has been completed. While FLSH_PEND = 1, further flash write requests are ignored.
Updating Individual Bytes in Flash Memory
The original state of a flash byte is 0xFF (all bits are 1). Once a value other than 0xFF is written to a flash
memory cell, overwriting with a different value usually requires that the cell be erased first. Since cells
cannot be erased individually, the page has to be first copied to RAM, followed by a page erase. After
this, the page can be updated in RAM and then written back to the flash memory.
Flash Erase Procedures
Flash erasure is initiated by writing a specific data pattern to specific SFR registers in the proper sequence.
These special pattern/sequence requirements prevent inadvertent erasure of the flash memory.
The mass erase sequence is:
Write 1 to the FLSH_MEEN bit (SFR 0xB2[1]).
Write the pattern 0xAA to the FLSH_ERASE (SFR 0x94) register.
The mass erase cycle can only be initiated when the ICE port is enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543F-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC |
发布紧急采购，3分钟左右您将得到回复。