收藏本站
参数资料
型号： 71M6543F-IGT/F
厂商： MAXIM INTEGRATED PRODUCTS INC
元件分类： 模拟信号调理
英文描述： SPECIALTY ANALOG CIRCUIT, PQFP100
封装： LEAD FREE, LQFP-100
文件页数： 110/157页
文件大小： 2178K
代理商： 71M6543F-IGT/F
71M6543F/H and 71M6543G/GH Data Sheet
56
2008–2011 Teridian Semiconductor Corporation
v1.2
Table 46 shows the I/O RAM registers used for temperature and battery measurement.
If TEMP_PWR selects VBAT_RTC when the battery is nearly discharged, the temperature
measurement may not finish. In this case, firmware may complete the measurement by selecting
V3P3D (TEMP_PWR = 1).
Table 46: I/O RAM Registers for Temperature and Battery Measurement
Name
Location
Rst
Wk
Dir
Description
TBYTE_BUSY
28A0[3]
0
R
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
TEMP_PER[2:0]
28A0[2:0]
0
–
R/W
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN, BRN, LCD, or SLP).
TEMP_PER
Time
0
Manual updates (see TEMP_START)
1-6
2 ^ (3+TEMP_PER) (seconds)
7
Continuous
TEMP_BAT
28A0[4]
0
–
R/W
Causes VBAT to be measured whenever a
temperature measurement is performed.
TEMP_START
28B4[6]
0
–
R/W
TEMP_PER[2:0] must be zero in order for TEMP_START
to function. If TEMP_PER[2:0] = 0, then setting
TEMP_START starts a temperature measurement.
Ignored in SLP and LCD modes. Hardware clears
TEMP_START when the temperature measurement is
complete.
TEMP_PWR
28A0[6]
0
–
R/W
Selects the power source for the temperature sensor:
1 = V3P3D, 0 = VBAT_RTC. This bit is ignored in
SLP and LCD modes, where the temperature sensor is
always powered by VBAT_RTC.
TEMP_BSEL
28A0[7]
0
–
R/W
Selects which battery is monitored by the
temperature sensor: 1 = VBAT, 0 = VBAT_RTC
TEMP_TEST[1:0]
2500[1:0]
0
–
R/W
Test bits for the temperature monitor VCO.
TEMP_TEST must be 00 in regular operation. Any
other value causes the VCO to run continuously with
the control voltage described below.
TEMP_TEST
Function
00
Normal operation
01
Reserved for factory test
1X
Reserved for factory test
STEMP[10:3]
STEMP[2:0]
2881[7:0]
2882[7:5]
R
The result of the temperature measurement.
The STEMP[10:0] value may be obtained in C with a
single 16-bit read and divide by 32 operation as
follows:
volatile int16_t xdata STEMP _at_0x2881;
fa = (float)(STEMP/32);
BSENSE[7:0]
2885[7:0]
–
R
The result of the battery measurement.
BCURR
2704[3]
0
R/W
Connects a 100 A load to the battery selected by
TEMP_BSEL.
2.5.6
71M6xx3 Temperature Sensor
相关PDF资料
PDF描述
71M6543H-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543F-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543H-IGT/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543G-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
71M6543GH-IGTR/F SPECIALTY ANALOG CIRCUIT, PQFP100
相关代理商/技术参数
参数描述
71M6543F-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*