- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6543F-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6543F-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 128/157页 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页当前第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
71M6543F/H and 71M6543G/GH Data Sheet
72
2008–2011 Teridian Semiconductor Corporation
v1.2
disabling the watchdog. SFMM and SFMS need to be written to in sequence in order to invoke SFM. This
sequential write process prevents inadvertent entering of SFM. The sequence for invoking SFM is:
First, write to SFMM (I/O RAM 0x2080) register. The value written to this register defines the SFM mode.
o
0xD1: Mass Erase mode. A Flash Mass erase cycle is invoked upon entering SFM.
o
0x2E: Flash Read back mode. SFM is entered for Flash read back purposes. Flash writes
will not be blocked and it is up to the user to guarantee that only previously unwritten
locations are written. This mode is not accessible when SPI secure mode is set.
o
SFM is not invoked if any other pattern is written to the SFMM register.
Next, write 0x96 to the SFMS (I/O RAM 0x2081) register. This write invokes SFM provided that the
previous write operation to SFMM met the requirements. Writing any other pattern to this register
does not invoke SFM. Additionally, any write operations to this register automatically reset the
previously written SFMM register values to zero.
SFM Details
The following occurs upon entering SFM.
The CE is disabled.
The MPU is halted. Once the MPU is halted it can only be restarted with a reset. This reset can be
accomplished with the RESET pin, a watchdog reset, or by cycling power (without battery at the
VBAT pin).
The Flash control logic is reset in case the MPU was in the middle of a Flash write operation or Erase
cycle.
Mass erase is invoked if specified in the SFMM (I/O RAM 0x2080) register (see Invoking SFM, above).
The SECURE bit (SFR 0xB2[6]) is cleared at the end of this and all Mass Erase cycles.
All SPI read and write operations now refer to Flash instead of XRAM space.
The SPI host can access the current state of the pending multi-cycle Flash access by performing a 4-byte
SPI write of any address and checking the status field.
All SPI write operations in SFM mode must be 6-byte write transactions that write two bytes to an even
address. The write transactions must contain a command byte of 0x00 which is the form that does not
create an MPU interrupt. Auto incrementing is disabled for write operations.
SPI read transactions can make use of auto increment and may access single bytes. The command byte
must always be 0x80 in SFM read transactions.
SPI commands in SFM
Interrupts are not generated in SFM since the MPU is halted. The format of the commands is shown in the
SPI Transactions description on Page 69.SPI Transactions
2.5.13 Hardware Watchdog Timer
An independent, robust, fixed-duration, watchdog timer (WDT) is included in the 71M6543. It uses the
RTC crystal oscillator as its time base and must be refreshed by the MPU firmware at least every
1.5 seconds. When not refreshed on time, the WDT overflows and the part is reset as if the RESET pin
were pulled high, except that the I/O RAM bits are in the same state as after a wake-up from SLP or LCD
modes (see the I/O RAM description in 5.2 for a list of I/O RAM bit states after RESET and wake-up).
Four thousand, one hundred CK32 cycles (or 125 ms) after the WDT overflow, the MPU is launched from
program address 0x0000.
The watchdog timer is also reset when the internal signal WAKE=0 (see 3.4 Wake-Up Behavior). The
WDT is disabled when the ICE_E pin is pulled high.
For details, see 3.3.4 Watchdog Timer (WDT) Reset.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543F-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC |
发布紧急采购，3分钟左右您将得到回复。