- 您现在的位置：买卖IC网 > PDF目录68811 > 71M6543F-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6543F-IGT/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 111/157页 |
| 文件大小： | 2178K |
| 代理商： | 71M6543F-IGT/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页当前第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
71M6543F/H and 71M6543G/GH Data Sheet
v1.2
2008–2011 Teridian Semiconductor Corporation
57
The 71M6xx3 includes an on-chip temperature sensor for determining the temperature of its bandgap
reference. The primary use of the temperature data is to determine the magnitude of compensation
required to offset the thermal drift in the system for the compensation of the current measurement
performed by the71M6xx3. See the 71M6xxx Data Sheet for the equation to calculate temperature from the
71M6xx3 STEMP[10:0] reading. Also, see 4.5 Metrology Temperature Compensation on page 89.
See 2.2.8.3 Control of the 71M6xx3 Isolated Sensor on page 22 for information on how to read the
STEMP[10:0] information from the 71M6xx3.
2.5.7
71M6543 Battery Monitor
The 71M6543 temperature measurement circuit can also monitor the batteries at the VBAT and
VBAT_RTC pins. The battery to be tested (i.e., VBAT or VBAT_RTC pin) is selected by TEMP_BSEL (I/O
RAM 0x28A0[7]).
When TEMP_BAT (I/O RAM 0x28A0[4]) is set, a battery measurement is performed as part of each
temperature measurement. The value of the battery reading is stored in register BSENSE[7:0] (I/O RAM
0x2885). The following equations are used to calculate the voltage measured on the VBAT pin (or
VBAT_RTC pin) from the BSENSE[7:0] and STEMP[10:0] values. The result of the equation below is in volts.
A slightly different equation is used for MSN mode and BRN mode, as follows.
In MSN mode, TEMP_PWR = 1 use:
V
STEMP
V
BSENSE
V
RTC
orVBAT
VBAT
000297
.
0
0246
.
0
)
142
(
3
.
3
)
_
(
+
+
=
In BRN mode, TEMP_PWR = TEMP_BSEL use:
V
STEMP
V
BSENSE
V
RTC
orVBAT
VBAT
000328
.
0
0255
.
0
)
142
(
291
.
3
)
_
(
+
+
=
In MSN mode, a 100 A de-passivation load can be applied to the selected battery (i.e., selected by the
TEMP_BSEL bit) by setting the BCURR (I/O RAM 0x2704[3]) bit. Battery impedance can be measured by
taking a battery measurement with and without BCURR. Regardless of the BCURR bit setting, the battery
load is never applied in BRN, LCD, and SLP modes.
2.5.8
71M6xx3 VCC Monitor
The 71M6xx3 monitors its VCC pin voltage. The voltage of the VCC pin can be obtained by the 71M6543
by issuing a read command to the 71M6xx3. The 71M6543 must request both the VSENSE[7:0] and
STEMP[10:0] values from the 71M6xx3. See the 71M6xxx Data Sheet for the equation to calculate the
71M6xx3 VCC pin voltage from the VSENSE[7:0] and STEMP[10:0] values read from the 71M6xx3.
See 2.2.8.3 Control of the 71M6xx3 Isolated Sensor on page 22 for information on how to read
VSENSE[7:0] and STEMP[10:0] from the 71M6xx3 remote sensors.
2.5.9
UART and Optical Interface
The 71M6543 provides two asynchronous interfaces, UART0 and UART1. Both can be used to connect
to AMR modules, user interfaces, etc., and also support a mechanism for programming the on-chip flash
memory.
Referring to Figure 14, UART1 includes an interface to implement an IR/optical port. The pin OPT_TX is
designed to directly drive an external LED for transmitting data on an optical link. The pin OPT_RX has
the same threshold as the RX pin, but can also be used to sense the input from an external photo detector
used as the receiver for the optical link. OPT_TX and OPT_RX are connected to a dedicated UART port
(UART1).
The OPT_TX and OPT_RX pins can be inverted with configuration bits OPT_TXINV (I/O RAM 0x2456[0])
and OPT_RXINV (I/O RAM 0x2457[1]), respectively. Additionally, the OPT_TX output may be modulated at
38 kHz. Modulation is available in MSN and BRN modes (see Table 62). The OPT_TXMOD bit (I/O RAM
0x2456[1]) enables modulation. The duty cycle is controlled by OPT_FDC[1:0] (I/O RAM 0x2457[5:4]) ,
which can select 50%, 25%, 12.5%, and 6.25% duty cycle. A 6.25% duty cycle means that OPT_TX is
low for 6.25% of the period.
When not needed for UART1, OPT_TX can alternatively be configured as SEGDIO51. Configuration is
via the OPT_TXE[1:0] (I/O RAM 0x2456[3:2]) field and LCD_MAP[51] (I/O RAM 0x2405[0]). The
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6543H-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543F-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543H-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543GH-IGTR/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543F-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543FT-IGT/F | 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube |
| 71M6543FT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel |
| 71M6543G | 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543GH | 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC |
发布紧急采购，3分钟左右您将得到回复。