- 您现在的位置：买卖IC网 > PDF目录68812 > 71M6543GH-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6543GH-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 121/157页 |
| 文件大小： | 2178K |
| 代理商： | 71M6543GH-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页当前第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
71M6543F/H and 71M6543G/GH Data Sheet
66
2008–2011 Teridian Semiconductor Corporation
v1.2
For example, if LCD_MAP[46] = 1, then pin 93 (TMUX2OUT/SEG46) is configured as SEG46, and if
LCD_MAP[46]=0, then pin 93 is configured as TMUX2OUT.
The SEG pins with alternate ICE interface function (see pins 56-58 in Figure 43) are forced to their
alternate ICE interface function (i.e., E_RXTX, E_TCLK and E_RST) if the ICE_E pin (pin 59) is driven
high, and in this case, the bits LCD_MAP[50:48] (I/O RAM 0x2405[2:0]) bits are “don’t care” bits. If the
ICE_E pin is driven low, then LCD_MAP[50:48] bits must written with 1 in order to configure these pins as
SEG pins. If the ICE_E pin is low and LCD_MAP[50:48] are written with 0, then these pins are tied to an
internal pullup.
2.5.11 EEPROM Interface
The 71M6543 provides hardware support for either a two-pin or a three-wire (-wire) type of EEPROM
interface. The interfaces use the EECTRL (SFR 0x9F) and EEDATA (SFR 0x9E) registers for communication.
2.5.11.1 Two-pin EEPROM Interface
The dedicated 2-pin serial interface communicates with external EEPROM devices. The interface is
multiplexed onto the SEGDIO2 (SDCK) and SEGDIO3 (SDATA) pins and is selected by setting
DIO_EEX[1:0] = 01 (I/O RAM 0x2456[7:6]). The MPU communicates with the interface through the SFR
registers EEDATA and EECTRL. If the MPU wishes to write a byte of data to the EEPROM, it places the
data in EEDATA and then writes the Transmit code to EECTRL. This initiates the transmit operation which
is finished when the BUSY bit falls. INT5 is also asserted when BUSY falls. The MPU can then check the
RX_ACK bit to see if the EEPROM acknowledged the transmission.
A byte is read by writing the Receive command to EECTRL and waiting for the BUSY bit to fall. Upon
completion, the received data is in EEDATA. The serial transmit and receive clock is 78 kHz during each
transmission, and then holds in a high state until the next transmission. The EECTRL bits when the two-pin
interface is selected are shown in Table 55.
Table 55: EECTRL Bits for 2-pin Interface
Status
Bit
Name
Read/
Write
Reset
State
Polarity
Description
7
ERROR
R
0
Positive
1 when an illegal command is received.
6
BUSY
R
0
Positive
1 when serial data bus is busy.
5
RX_ACK
R
1
Positive
1 indicates that the EEPROM sent an ACK bit.
4
TX_ACK
R
1
Positive
1 indicates when an ACK bit has been sent to the
EEPROM.
3:0
CMD[3:0]
W
0000
Positive
CMD[3:0]
Operation
0000
No-op command. Stops the I
2C clock
(SDCK). If not issued, SDCK keeps
toggling.
0010
Receive a byte from the EEPROM and
send ACK.
0011
Transmit a byte to the EEPROM.
0101
Issue a STOP sequence.
0110
Receive the last byte from the
EEPROM and do not send ACK.
1001
Issue a START sequence.
Others
No operation, set the ERROR bit.
The EEPROM interface can also be operated by controlling the DIO2 and DIO3 pins directly. The
direction of the DIO line can be changed from input to output and an output value can be written
with a single write operation, thus avoiding collisions (see Table 14 Port Registers (SEGDIO0-15)).
Therefore, no resistor is required in series SDATA to protect against collisions.
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
| 71M6543GHT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel |
| 71M6543G-IGT/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543G-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
发布紧急采购，3分钟左右您将得到回复。