- 您现在的位置：买卖IC网 > PDF目录68812 > 71M6543GH-IGTR/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | 71M6543GH-IGTR/F |
| 厂商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封装： | LEAD FREE, LQFP-100 |
| 文件页数： | 141/157页 |
| 文件大小： | 2178K |
| 代理商： | 71M6543GH-IGTR/F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页当前第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页
71M6543F/H and 71M6543G/GH Data Sheet
84
2008–2011 Teridian Semiconductor Corporation
v1.2
Table 66: Clear Events for WAKE flags
Flag
Wake on:
Clear Events
WF_TMR
Timer expiration
WAKE falls
WF_PB
PB pin high level
WAKE falls
WF_RX
Either edge RX pin
WAKE falls
WF_DIO4
SEGDIO4 rising edge
WAKE falls
WF_DIO52
SEGDIO52 high level
WAKE falls
WF_DIO55
If OPT_RXDIS = 1 (I/O RAM 0x2457[2]),
wake on SEGDIO55 high
If OPT_RXDIS = 0
wake on either edge of OPT_RX
WAKE falls
WF_RST
RESET pin driven high
WAKE falls, WF_CSTART, WF_RSTBIT,
WF_OVF, WF_BADVDD
WF_RSTBIT
RESET bit is set (I/O RAM 0x2200[3])
WAKE falls, WF_CSTART, WF_OVF,
WF_BADVDD, WF_RST
WF_ERST
E_RST pin driven high and the ICE
interface must be enabled by driving the
ICE_E pin high.
WAKE falls, WF_CSTART, WF_RST,
WF_OVF, WF_RSTBIT
WF_OVF
Watchdog (WD) reset
WAKE falls, WF_CSTART, WF_RSTBIT,
WF_BADVDD, WF_RST
WF_CSTART
Cold-start (i.e., after the application of
first power)
WAKE falls, WF_RSTBIT, WF_OVF,
WF_BADVDD, WF_RST
Note:
“WAKE falls” implies that the internal WAKE signal has been reset, which happens automatically upon
entry into LCD mode or SLEEP mode (i.e., when the MPU sets the LCD_ONLY bit (I/O RAM 0x28B2[6]) or
the SLEEP (I/O RAM 0x28B2[7]) bit). When the internal WAKE signal resets, all wake flags are reset. Since
the various wake flags are automatically reset when WAKE falls, it is not necessary for the MPU to reset
these flags before entering LCD mode or SLEEP mode. Also, other wake events can cause the wake flag
to reset, as indicated above (e.g., the WF_RST flag can also be reset by any of the following flags setting:
WF_CSTART, WS_RSTBIT, WF_OVF, WF_BADVDD)
3.4.2
Wake on Timer
If the part is in SLP or LCD mode, it can be awakened by the Wake Timer. Until this timer times out, the
MPU is in reset due to the internal WAKE signal being low. When the Wake Timer times out, WAKE rises
and within three CK32 cycles, the MPU begins to execute. The MPU can determine that the timer woke it
by checking the WF_TMR (I/O RAM 0x28B1[2]) wake flag.
The Wake Timer begins timing when the part enters LCD or SLP mode. Its duration is controlled by the
WAKE_TMR[7:0] register (I/O RAM 0x2880). The timer duration is WAKE_TMR[7:0] +1 seconds.
The Wake Timer is armed by setting WAKE_ARM = 1 (I/O RAM 0x28B2[5]). It must be armed at least
three RTC cycles before either SLP or LCD modes are initiated. Setting WAKE_ARM presets the timer
with the value in WAKE_TMR and readies the timer to start when the MPU writes to the SLEEP (I/O RAM
0x28B2[7]) or LCD_ONLY (I/O RAM 0x28B2[6]) bits. The timer is neither reset nor disarmed when the
MPU wakes-up. Thus, once armed and set, the MPU continues to be awakened WAKE_TMR[7:0]
seconds after it requests SLP mode or LCD mode (i.e., once written, the WAKE_TMR[7:0] register holds
its value and does not have to be re-written each time the MPU enters SLP or LCD mode. Also, since
WAKE_TMR[7:0] is non-volatile, it also holds its value through resets and power failures).
3.5
Data Flow and MPU/CE Communication
The data flow between the Compute Engine (CE) and the MPU is shown in Figure 26. In a typical application,
the 32-bit CE sequentially processes the samples from the ADC inputs, performing calculations to measure
相关PDF资料 |
PDF描述 |
|---|---|
| 71M6543GH-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
| 71M6543GHT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel |
| 71M6543G-IGT/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543G-IGTR/F | 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
发布紧急采购，3分钟左右您将得到回复。