- 您现在的位置：买卖IC网 > PDF目录370133 > 7548 (Renesas Technology Corp.) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF资料下载
参数资料
| 型号： | 7548 |
| 厂商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 单芯片8位CMOS微机 |
| 文件页数： | 27/73页 |
| 文件大小： | 1255K |
| 代理商： | 7548 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
Rev.2.00
REJ03B0210-0200
Mar 15, 2007
Page 27 of 70
7548 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Output compare
7548 group has 3-output compare channels. Each channel (0 to
2) has the same function and can be used to output waveform by
using count value of Timer A.
Three output compare channels share the registers with the input
capture (one channel), but their individual circuits operate
independently so that all the channels can be used at the same
time.
To use each compare channel, set “1” to the compare x (x = 0, 1,
2, 3) output port bit and set the port direction register
corresponding to compare channel to output mode.
The compare value for each channel is set to the capture/compare
register (low-order) and capture/compare register (high-order).
Writing to the register for each channel is controlled by setting
value of capture/compare register RW pointer. Writing to each
register is in the following order;
1.Set the corresponding compare latch to the capture/compare
register RW pointer.
2.Write a value to the capture/compare register (low-order)
and capture/compare register (high-order). (It doesn’t care
even if either low-order or high-order is written early.)
3.Set “1” to the compare latch y (y = 00, 01, 10, 11, 20, 21)
re-load bit.
When “1” is set to the compare latch y re-load bit, the value set to
the compare register is loaded to compare latch when the next
timer underflow.
After loading, re-load bit is set to “0” automatically.
When the count value of timer A matches the compare latch
setting value, a trigger to the compare output circuit is generated.
The trigger can be enabled or disabled using the compare x
trigger enable bit. When the compare x trigger enable bit is set to
1, the output waveform from the port is as follows.
When the value of the compare x output level latch is “0”
High level at compare latch x0 match
Low level at compare latch x1 match
When the value of the compare x output level latch is “1”
Low level at compare latch x0 match
High level at compare latch x1 match
The output waveform does not change if the compare x trigger
enable bit is set to 0, so the port output remains fixed at high or
low level.
The compare output level of each channel can be confirmed by
reading the compare x output status bit.
Compare interrupt is available when match of each compare
channel and timer count value. The interrupt request from each
channel can be disabled or enabled by setting value of compare
latch y interrupt source selection bit.
Notes on Output Compare
(1) If timer A is stopped, when a value is written to the capture/
compare register it is immediately transferred to the
compare latch. In addition, if timer A is stopped and the
compare x trigger enable bit is set to “1”, the output latch is
initialized.
(2) Do not write the same data to both of compare latch x0 and
x1.
(3) When setting value of the compare latch is larger than timer
setting value, compare match signal is not generated.
Accordingly, the output waveform is fixed to “L” or “H”
level.
However, when setting value of another compare latch is
smaller than timer setting value, this compare match signal
is generated. Accordingly, compare interrupt occurs.
(4) When the compare x trigger enable bit is cleared to “0”
(disabled), the match trigger to the waveform output circuit
is disabled, and the output waveform can be fixed to “L” or
“H” level.
However, in this case, the compare match signal is
generated.
Accordingly, compare interrupt occurs.
Fig 27. Structure of capture/compare register
Fig 28. Structure of capture/compare register RW
pointer
Fig 29. Structure of compare register re-load register
Fig 30. Structure of capture/compare port register
b7
b0
Capture/Compare register (low-order)
(CRAL: address 0010
16
, initial value: 00
16
)
b7
b0
Capture/Compare register (high-order)
16
, initial value: 00
16
)
b7
b0
Capture/Compare register RW pointer
16
, initial value: 00
16
)
Cb2 b1 b0
0 0 0 : Compare latch 00
Not used (returns “0” when read)
b7
b0
Compare register re-load register
16
, initial value: 00
16
)
Compare latch 00, 01 re-load bit
Compare latch 10, 11 re-load bit
Compare latch 20, 21 re-load bit
Not used (returns “0” when read)
b7
b0
Capture/Compare port register
16
, initial value: 00
16
)
C0: Capture from P0
1: Low-speed on-chip oscillator/16
C0: P1
0
1: P1
0
is I/O port
C0: P1
1
1: P1
1
is I/O port
C0: P1
2
1: P1
2
is I/O port
Not used (returns “0” when read)
相关PDF资料 |
PDF描述 |
|---|---|
| 7549 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 75HQ | SCHOTTKY RECTIFIER |
| 75HQ030 | SCHOTTKY RECTIFIER |
| 75HQ035 | SCHOTTKY RECTIFIER |
| 75HQ040 | SCHOTTKY RECTIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 7548_07 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Standard Characteristics |
| 7548_0710 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 75481-001 | 功能描述:集管和线壳 BACKPANEL PINS RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 75481-002 | 功能描述:集管和线壳 BERGPIN - WITH LARGE STA-R RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 75481-004 | 功能描述:集管和线壳 BERGPIN RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。