- 您现在的位置：买卖IC网 > PDF目录370133 > 7548 (Renesas Technology Corp.) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF资料下载
参数资料
| 型号： | 7548 |
| 厂商： | Renesas Technology Corp. |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 单芯片8位CMOS微机 |
| 文件页数： | 31/73页 |
| 文件大小： | 1255K |
| 代理商： | 7548 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页当前第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
Rev.2.00
REJ03B0210-0200
Mar 15, 2007
Page 31 of 70
7548 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Input capture
7548 group has 1-input capture channel and can be used to
capture count value of Timer A.
Input capture shares the registers with three output capture
channels, but their individual circuits operate independently so
that all the channels can be used at the same time.
To use input capture, set the input capture port selection bits. If
P0
3
is selected, set the P0
3
direction register to 0. When an input
capture trigger is input to the input capture circuit, the count
value of timer A is saved to the capture latches. The timer count
value at the rising edge of the external input trigger is saved to
capture latch 00, and the timer count value at the falling edge of
the external input trigger is saved to capture latch 01. Capture
latch 00 and capture latch 01 can be read using the following
procedure.
1.Set the capture/compare register R/W pointer to the read
target address.
2.Read the high-order bits of the capture/compare registers,
then read the low-order bits of the capture/compare regis-
ters. (Read both the capture/compare registers in the
sequence of high-order bits followed by low-order bits.)
The count value of timer can be retained by software by capture
y (y = 00, 01, 10, 11) software trigger bit too. When “1” is set to
this bit, count value of timer is retained to the corresponded
capture latch.
When reading from the capture y software trigger bit is executed,
“0” is read out.
Notes on Input Capture
When the low-speed on-chip oscillator output or X
CIN
input
clock is selected as the count source of timer A, input capture
can be used only if the same clock source is selected as
φ
SOURCE and as the count source of timer A.
When writing “1” to capture y software trigger bit of capture
latch 00 and 01 at the same time, or external trigger and
software trigger occur simultaneously, if capture latches 00
and 01 are input simultaneously, the set value of capture 0
status bit is undefined.
When setting the interrupt active edge selection bit and noise
filter clock selection bit of capture 0 the interrupt request bit
may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
(1) Set the capture interrupt enable bit to “0” (disabled).
(2) Set the interrupt edge selection bit or noise filter clock
selection bit.
(3) Set the corresponding interrupt request bit to “0” after 1 or
more instructions have been executed.
(4) Set the capture interrupt enable bit to “1” (enabled).
When the capture interrupt is used as the interrupt for return
from stop mode, set the capture 0 noise filter clock selection
bits to “00 (Filter stop)”.
Fig 38. Structure of capture software trigger register
Fig 39. Structure of capture mode register
b7
b0
Capture software trigger register
16
, initial value: 00
16
)
CaCapture 00 software trigger occurs by setting “1”
to this bit. (returns “0” when read)
CaCapture 01 software trigger occurs by setting “1”
to this bit. (returns “0” when read)
Not used (returns “0” when read)
b7
b0
Cab1 b0
0 0 : Rising and falling edge
Cab1 b0
IN
IN
0 0 : Filter)
IN
)/8
Not used (returns “0” when read)
Capture mode register
16
, initial value: 00
16
)
相关PDF资料 |
PDF描述 |
|---|---|
| 7549 | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 75HQ | SCHOTTKY RECTIFIER |
| 75HQ030 | SCHOTTKY RECTIFIER |
| 75HQ035 | SCHOTTKY RECTIFIER |
| 75HQ040 | SCHOTTKY RECTIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 7548_07 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Standard Characteristics |
| 7548_0710 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 75481-001 | 功能描述:集管和线壳 BACKPANEL PINS RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 75481-002 | 功能描述:集管和线壳 BERGPIN - WITH LARGE STA-R RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
| 75481-004 | 功能描述:集管和线壳 BERGPIN RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector |
发布紧急采购，3分钟左右您将得到回复。