收藏本站
参数资料
型号： 7548
厂商： Renesas Technology Corp.
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 单芯片8位CMOS微机
文件页数： 39/73页
文件大小： 1255K
代理商： 7548
Rev.2.00
REJ03B0210-0200
Mar 15, 2007
Page 39 of 70
7548 Group
PRELIMINARY
Notice: This is not a final specification.
Some parametric limits are subject to change.
Watchdog Timer
The watchdog timer gives a means for returning to a reset status
when the program fails to run on its normal loop due to a runaway.
The watchdog timer consists of an 8-bit watchdog timer H and an
8-bit watchdog timer L, being a 16-bit counter. The operation of
the watchdog timer is controlled by bits 2 to “0” in function set
ROM data 2 and the watchdog timer control register.
Watchdog timer disable bit
When the watchdog timer disable bit (bit 1 in function set ROM
data 2(FSROM2)) is set to “0”, the watchdog timer is enabled
and starts counting after reset.
Setting this bit to “1” does not operate the watchdog timer.
This bit cannot be rewritten by executing the instruction.
To use the watchdog timer, always set this bit to “0”.
After reset, the watchdog timer cannot start counting by a program.
Watchdog timer source clock selection bit
The count source of the watchdog timer is selected by the
watchdog timer source clock selection bit (bit 0 in FSROM2).
This bit cannot be rewritten by executing the instruction.
When this bit is set to “0”, the count source is always set to the
low-speed on-chip oscillator output/16.
When this bit is set to “1”, the count source is set to
φ
SOURCE/
16.
φ
SOURCE is changed by setting the clock selection bits (bits
5 and 4 in the clock mode register (CLKM: address 0037
16
)).
Watchdog timer H count source selection bit
The count source of watchdog timer H is selected by the
watchdog timer control register (WDTCON: address 0039
16
).
When the watchdog timer H count source selection bit (bit 7 in
WDTCON) is set to “0”, the count source is set to an underflow
signal from watch dog timer L. When this bit is set to “1”, the
clock selected as the count source of watchdog timer L is input to
watchdog timer H.
The initial value of this bit after releasing reset can be set by the
bit 2 in FSROM2.
Watchdog Timer Operation
Resetting or writing any data to WDTCON sets watchdog timer H
to “FF
16
” and watchdog timer L to “FF
16
”. When the watchdog
timer starts, the selected clock is counted and internal reset occurs
by the watchdog timer H underflow. Writing to WDTCON is
usually programmed to be performed before underflow.
Reading WDTCON reads the values of the high-order 6 bits in
the watchdog timer H counter and the watch dog timer count
source selection bit.
The following shows the time to watchdog timer underflow after
writing to the watchdog timer control register.
The example applies when the X
IN
input clock is selected as
φ
SOURCE and f(X
IN
) = 8 MHz.
Watchdog timer H count source selection bit = 0: 131.072 ms
Watchdog timer H count source selection bit = 1: 512
μ
s
Fig 51. Structure of Function set ROM data 2
Fig 52. Structure of watchdog timer control register
Fig 53. Block diagram of watchdog timer
Watchdog timer source clock selection bit
0 : Low-speed on-chip oscillator/16
1 : System clock/16
Watchdog timer start selection bit
0 : Start watchdog timer
1 : Stop watchdog timer
Watchdog timer H count source initial value
selection bit
0 : Initial value of bit 7 of WDTCON
after reset release is “0”
1 : Initial value of bit 7 of WDTCON
after reset release is “1”
STP instruction function selection bit
0 : System enters into the stop mode
at the STP instruction execution
1 : Internal reset occurs at the STP
instruction execution
Low-speed on-chip oscillator control bit
(Note 1)
0 : Stop of low-speed on-chip oscillator
disabled
1 : Stop of low-speed on-chip oscillator
enabled
Set “0” to these bits certainly.
b7
Function set ROM data 2
FSROM2 (FFDA
16
)
b0
Note 1:
If “0” is set to this bit, it is not possible to write “1” to bit 0 in the clock
mode register. Also, the low-speed on-chip oscillator does not stop
even if the STP instruction is executed.
Watchdog timer H (read only for
high-order 6-bit)
Not used (returns “0” when read)
Watchdog timer H count source
selection bit
0 : Watchdog timer L underflow
1 : Low-speed on-chip oscillator/16
or
φ
SOURCE/16
Watchdog timer control register (Note)
(WDTCON: address 0039
16
,
initial value: X0111111
2
)
b7
b0
Note:
The initial value of this register is changes by setting of
function set ROM data 2.
Watchdog timer H (8)
Data bus
Watchdog timer L (8)
“FF
16
” is set at
WDTCON writing
1/16
φ
SOURCE
Low-speed on-chip
oscillator
Watchdog timer source
clock selection bit
(bit 0 of FSROM2)
Watchdog timer start
selection bit
(bit 1 of FSROM2)
Reset
circuit
Internal reset
STP instruction function
selection bit
(bit 3 of FSROM2)
STP Instruction
Reset pin input
Watchdog timer H
count source selection bit
(bit 7 of WDTCON)
Watchdog timer H count source
initial value selection bit
(bit 2 of FSROM2)
FSROM2: Function set ROM data 2
WDTCON: Watchdog timer control register
CPUM: CPU mode register
“FF
16
” is set at
WDTCON writing
Initial value setting
after releasing reset
相关PDF资料
PDF描述
7549 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
75HQ SCHOTTKY RECTIFIER
75HQ030 SCHOTTKY RECTIFIER
75HQ035 SCHOTTKY RECTIFIER
75HQ040 SCHOTTKY RECTIFIER
相关代理商/技术参数
参数描述
7548_07 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:Standard Characteristics
7548_0710 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
75481-001 功能描述:集管和线壳 BACKPANEL PINS RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
75481-002 功能描述:集管和线壳 BERGPIN - WITH LARGE STA-R RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
75481-004 功能描述:集管和线壳 BERGPIN RoHS:否 产品种类:1.0MM Rectangular Connectors 产品类型:Headers - Pin Strip 系列:DF50 触点类型:Pin (Male) 节距:1 mm 位置/触点数量:16 排数:1 安装风格:SMD/SMT 安装角:Right 端接类型:Solder 外壳材料:Liquid Crystal Polymer (LCP) 触点材料:Brass 触点电镀:Gold 制造商:Hirose Connector
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*