- 您现在的位置：买卖IC网 > Datasheet目录613 > 91911-2 (TE Connectivity)PREM SDE DIE COAXICON RG 180 Datasheet资料下载
参数资料
| 型号： | 91911-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/3页 |
| 文件大小： | 0K |
| 描述： | PREM SDE DIE COAXICON RG 180 |
| 标准包装： | 1 |
| 系列： | * |
Indenter Die
Center Contact
Crimping Chamber
Anvil Die
SDE Crimping Die
Assembly 91911-[ ]
Retaining
Screw Hole
Ferrule Crimping
Chamber(s)
Instruction Sheet
408-8581
14 MAY 13 Rev C
crimping chamber crimps the center contact onto the
center conductor of the coaxial cable.
3. DIE INSTALLATION
1. Close the tool frame handles until the ratchet
releases, then allow the tool handles to open fully.
2. Install the anvil die into the movable jaw of the
tool frame. Align the die with the retaining screw
hole, then secure the die with the retaining screw.
DO NOT fully tighten.
3. Install the indenter die into the stationary jaw of
the tool frame. Slowly close the tool handles,
allowing the dies to align themselves. After the anvil
die has mated with the indenter die, place a
1.57 ±0.05-mm [.062 ±.002-in.] diameter copper bus
bar into the center contact crimping chamber of the
die assembly. Secure the die with the retaining
screw. DO NOT fully tighten.
4. Close the tool handles completely.
5. Securely tighten both retaining screws.
DIE ASSEMBLY
91911-1
91911-2
91911-3
91911-4
CONNECTOR DESCRIPTION
Miniature Threaded COAXICON* Connector
Subminiature COAXICON Connector
Figure 1
4. CRIMPING PROCEDURE
Select the appropriate size cable and connector. The
wire size and insulation diameter must be within the
specified range for the connector.
Initially, the crimp height should be verified before
crimping the center contact or ferrule. Refer to
Instruction Sheet 408-9930 included with the tool
frame for crimp height adjustment.
1. INTRODUCTION
SDE Crimping Die Assemblies 91911-[ ] are designed
to crimp the center contact and ferrule of COAXICON
connectors when used in PRO-CRIMPER* III Frame
Assembly 354940-1. Refer to Figure 1 for die
assembly-to-connector cross-reference.
NOTE
i
For detailed information on cable strip lengths and
proper assembly of the connector, refer to the
instructions packaged with the connector. Make
sure that the ferrule has been placed onto the
cable, and that the cable braided shield is flared
away from the cable.
NOTE
i
Dimensions in this document are in metric units
[with U.S. customary units in brackets]. Figures and
illustrations are for reference only and are not
drawn to scale.
Proceed as follows:
4.1. Crimping the Center Contact (See Figure 2)
1. Close the tool handles until the dies are partially
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
Each die assembly consists of an indenter die and an
anvil die. Each die is held in the tool frame assembly
by a single screw (included with the tool frame).
When closed, the dies form two or three crimping
chambers. The larger crimping chambers crimp the
ferrule onto the coaxial cable, and the smaller
closed.
2. Assemble the center contact onto the cable
center conductor. Place the center contact in the
smallest crimping chamber of the anvil die. Make
sure the flange on the end of the center contact
butts against the die.
3. Holding the cable in place, close the tool handles
until the ratchet releases.
4. Allow the tool handles to open fully and remove
the crimped center contact from the dies.
?2013 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 3
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 91912-3 | TOOL CRIMPING DIE COAXICON |
| 91963-2 | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91911-21109 | 功能描述:板对板与夹层连接器 9P HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21109LF | 功能描述:板对板与夹层连接器 CONAN HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21111 | 功能描述:板对板与夹层连接器 CONAN HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21111LF | 功能描述:板对板与夹层连接器 CONAN STR SMT HDR W/PEG RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21115LF | 功能描述:CONAN CONN HDR 制造商:amphenol fci 系列:* 零件状态:在售 标准包装:49 |
发布紧急采购，3分钟左右您将得到回复。