- 您现在的位置：买卖IC网 > Datasheet目录613 > 91912-3 (TE Connectivity)TOOL CRIMPING DIE COAXICON Datasheet资料下载
参数资料
| 型号： | 91912-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 1/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPING DIE COAXICON |
| 标准包装： | 5 |
| 系列： | Certi-Crimper |
| 压接手柄： | A9996-ND |
| 连接器类型： | 同轴连接器 |
| 配用： | 201144-3-ND - CONN SOCKET COAX STR 30GOLD |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q1389352 |
SDE Criming Die Assembly 91912-[ ]
Instruction Sheet
408-8582
21 NOV 11 Rev A
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
Indenter
Die
crimps the center contact onto the center conductor of
the coaxial cable. Each die is held in the ?
PRO-CRIMPER II hand tool jaws by a single screw.
1. Close the tool handles until the ratchet releases,
then allow the tool handles to open fully.
NOTE
i
Typical
Crimping Die
Assembly
Anvil
Die
Ferrule
Crimping
Chamber
Center Contact
Crimping Chamber
2. Install anvil die in the movable jaw of the tool
frame. Align the die with the retaining screw hole,
then secure die with the die-retaining screw. Do
NOT fully tighten.
3. Install indenter die in the stationary jaw of the tool
frame. Slowly close the tool handles, allowing the
dies to align themselves.
Once the anvil has entered the indenter, place a
copper bus bar (1.57-mm ± 0.05 mm ?
[.062-in. ± .002 in.] diameter) into the center
contact crimping chamber of the die assembly.
4. Close the tool handles completely.
5. Securely tighten both screws with the appropriate
Figure 1
1. INTRODUCTION
SDE (Four-Piece) Crimping Die Assemblies 91912-[ ]
are designed to crimp a variety of connectors when
used in PRO-CRIMPER* II Hand Tool Frame
screwdriver.
4. CRIMPING PROCEDURE
Select the appropriate cable size and connector. The
wire size and insulation diameter must be within the
specified range for the connector.
Assembly 354940-1. Refer to Figure 5 for a list of
connectors and their associated dies, as well as
detailed drawings of the crimping dies.
Catalog 1307191 provides a guide for cable- to-
NOTE
i
This tool is provided with a crimp height adjustment
feature. Initially, the crimp height should be verified.
Refer to Section 5, Crimp Height Adjustment, to
verify crimp height before using the tool.
connector selection. For connectors not referenced in
the catalog, contact TE Product Engineering for
recommendations.
Refer to instruction sheet 408-9930 for information
concerning PRO-CRIMPER II Hand Tool Frame
354940-1.
For detailed information on cable strip lengths and
proper assembly of the connector, refer to the
instructions packaged with the connector. Make sure
that the connector's ferrule has been placed onto the
cable, and that the cable's braided shield is flared
away from the cable. Then proceed as follows:
NOTE
i
Dimensions in this document are in metric units
[with U.S. customary units in brackets].
1. Close the tool handles until the dies are partially
closed.
2. DESCRIPTION
Each four-piece crimping die assembly consists of two
indenter dies and two anvil dies, which when closed
form two or three crimping chambers. The larger
crimping chambers crimp the ferrule of the connector
onto the coaxial cable. The smaller crimping chamber
2. Assemble the center contact onto the cable
center conductor and place the center contact in the
smallest crimping chamber of the anvil die. Make
sure the flange on the end of the center contact
butts against the die.
? 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company ?
All Rights Reserved
*Trademark
TOOLING ASSISTANCE CENTER 1-800-722-1111 ?
PRODUCT INFORMATION 1-800-522-6752
This controlled document is subject to change. ?
For latest revision and Regional Customer Service,
visit our website at www.te.com
1 of 4
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
LOC B
相关PDF资料 |
PDF描述 |
|---|---|
| 91963-2 | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91912-31331LF | 制造商:FCI 功能描述:Conn Board to Board HDR 31 POS 1mm Solder ST SMD T/R 制造商:FCI 功能描述:CONN BD TO BD HDR 31 POS 1MM SLDR ST SMD - Tape and Reel |
| 91912-4 | 功能描述:冲压机与冲模 PREM SDE DIE, MINI COAXICON RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 919-124J-71P | 功能描述:RF 连接器 MCX RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 919-124J-71PB | 制造商:Amphenol Corporation 功能描述:SPECIAL MCX JACK, 75 OHM, PC MOUNT - Bulk |
| 91912-5 | 功能描述:冲压机与冲模 PREM SDE DIE, MINI COAXICON RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。