- 您现在的位置：买卖IC网 > Datasheet目录613 > 91912-3 (TE Connectivity)TOOL CRIMPING DIE COAXICON Datasheet资料下载
参数资料
| 型号： | 91912-3 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/4页 |
| 文件大小： | 0K |
| 描述： | TOOL CRIMPING DIE COAXICON |
| 标准包装： | 5 |
| 系列： | Certi-Crimper |
| 压接手柄： | A9996-ND |
| 连接器类型： | 同轴连接器 |
| 配用： | 201144-3-ND - CONN SOCKET COAX STR 30GOLD |
| 相关产品： | A9996-ND - PRO CRIMPER HAND TOOL W/O DIES |
| 其它名称： | Q1389352 |
408-8582
Crimping the Center Contact
Plug
Contact
Cross Sectional View
Flange on
End of Contact
Center Contact in
Crimping Chamber
Anvil Die
Stripped
Cable
Jack
Contact
Figure 2
Crimping
Die
Flange on
End of Contact
Crimping
Die
crimp an improperly positioned ferrule. ?
3. Holding the cable in place, close the tool handles
until the ratchet releases.
4. Allow the tool handles to open fully and remove
the crimped center contact from the dies.
1. Insert the crimped center contact into the
CAUTION Make sure that both sides of the ferrule are started
evenly into the crimping chamber. Do not attempt to
!
5. Carefully close the tool handles until the ratchet
releases. ?
NOTE
i
connector body until the cable dielectric butts
against the dielectric inside the connector body or
until the center contact is securely positioned within
the connector. Make sure that the braided shield is
over the support sleeve of the connector body and
that no strands from the shield enter the connector
body.
2. Slide the ferrule up over the braided shield and
onto the connector until the ferrule butts against the
shoulder on the connector body.
3. Place the ferrule in the appropriate crimping
chamber of the anvil die so that the shoulder on the
connector body butts against the edge of the die.
Refer to the instruction sheet packaged with the
connector to determine the appropriate crimping
chamber for the ferrule. ?
4. While holding the assembly together, begin to
close the tool handles. Keep holding the assembly
until the dies have closed enough to clamp the
assembly in place.
Rev A
Crimping the Ferrule
Ferrule in ?
Crimping ?
Chamber on ?
Anvil Die
Figure 3
Shoulder on
Connector Body
Butts Against the
Edge of the Die
2 of 4
相关PDF资料 |
PDF描述 |
|---|---|
| 91963-2 | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
| 931800-1 | ELEC PWR UNIT W/O F/TRK OR HD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91912-31331LF | 制造商:FCI 功能描述:Conn Board to Board HDR 31 POS 1mm Solder ST SMD T/R 制造商:FCI 功能描述:CONN BD TO BD HDR 31 POS 1MM SLDR ST SMD - Tape and Reel |
| 91912-4 | 功能描述:冲压机与冲模 PREM SDE DIE, MINI COAXICON RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
| 919-124J-71P | 功能描述:RF 连接器 MCX RoHS:否 制造商:Bomar Interconnect 产品:Connectors 射频系列:BNC 型式:Jack (Female) 极性: 触点电镀:Gold 阻抗: 端接类型:Solder 主体类型:Straight Bulkhead 电缆类型: |
| 919-124J-71PB | 制造商:Amphenol Corporation 功能描述:SPECIAL MCX JACK, 75 OHM, PC MOUNT - Bulk |
| 91912-5 | 功能描述:冲压机与冲模 PREM SDE DIE, MINI COAXICON RoHS:否 制造商:Souriau 大小: 产品:Dies 类型:Crimping 描述/功能: |
发布紧急采购，3分钟左右您将得到回复。