- 您现在的位置：买卖IC网 > Datasheet目录613 > 91911-2 (TE Connectivity)PREM SDE DIE COAXICON RG 180 Datasheet资料下载
参数资料
| 型号： | 91911-2 |
| 厂商： | TE Connectivity |
| 文件页数： | 2/3页 |
| 文件大小： | 0K |
| 描述： | PREM SDE DIE COAXICON RG 180 |
| 标准包装： | 1 |
| 系列： | * |
408-8581
Crimping the Center Contact
Typical Die Assembly
Center Contact
Center Contact
Crimping Chamber
of Anvil Die
Upper and lower die posts must enter slot in contact in order to
CAUTION
crimp wire. If not properly aligned, damage to die set will occur.
!
Figure 2
4.2. Crimping the Ferrule (See Figure 3)
1. Insert the crimped center contact into the
connector body until the cable dielectric butts
against the dielectric inside the connector body or
Plug Center
Contact
Jack Center
Contact
Crimping the Ferrule
Flange
Against Die
Flange
Against Die
until the center contact is securely positioned within
the connector. Make sure that the braided shield is
over the support sleeve of the connector body and
that no strands from the shield enter the connector
body.
2. Slide the ferrule over the braided shield and onto
the connector until the ferrule butts against the
shoulder on the connector body.
3. Place the ferrule in the ferrule crimping chamber
of the anvil die so that the shoulder of the connector
body butts against the edge of the die.
Typical Die Assembly
Ferrule Crimping
Chamber of Anvil Die
NOTE
i
Refer to the instruction sheet packaged with the
connector to determine the appropriate crimping
chamber for the ferrule.
Shoulder of Ferrule
Against Edge of Die
Figure 3
to crimp an improperly positioned ferrule.
4. While holding the assembly together, close the
tool handles until the dies have closed enough to
hold the ferrule in place.
CAUTION Make sure that both sides of the ferrule are started
evenly into the crimping chamber. DO not attempt
!
5. Carefully close the tool handles until the ratchet
releases.
Rev C
6. Allow the tool handles to open fully, and remove
the crimped ferrule from the dies.
5. MAINTENANCE AND INSPECTION
The crimping die assembly is inspected before
shipment; however, it is recommended that the dies be
inspected immediately upon arrival at your facility to
ensure that the dies have not been damaged during
shipment.
The die assembly will perform correctly as long as:
(1) the product specified is correct for the application,
(2) the specified die assembly is used, (3) the die
assembly has been measured to ensure that the die
2 of 3
相关PDF资料 |
PDF描述 |
|---|---|
| 91912-3 | TOOL CRIMPING DIE COAXICON |
| 91963-2 | S.D.E.PREM.DIE ASSY 16-14 PIDG |
| 91964-2 | S.D.E.PREM.DIE ASSY 22-16 PIDG |
| 91965-2 | S.D.E.PREM.DIE ASSY 12-10 PIDG |
| 929013 | KNOCKOUT TOOL |
相关代理商/技术参数 |
参数描述 |
|---|---|
| 91911-21109 | 功能描述:板对板与夹层连接器 9P HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21109LF | 功能描述:板对板与夹层连接器 CONAN HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21111 | 功能描述:板对板与夹层连接器 CONAN HEADER RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21111LF | 功能描述:板对板与夹层连接器 CONAN STR SMT HDR W/PEG RoHS:否 制造商:JAE Electronics 系列:WP3 产品类型:Receptacles 节距:0.4 mm 叠放高度:1 mm 安装角: 位置/触点数量:50 排数:2 外壳材料:Plastic 触点材料:Copper Alloy 触点电镀:Gold 电压额定值:50 V 电流额定值:0.4 A |
| 91911-21115LF | 功能描述:CONAN CONN HDR 制造商:amphenol fci 系列:* 零件状态:在售 标准包装:49 |
发布紧急采购，3分钟左右您将得到回复。