参数资料
型号: A09-HASM-675
厂商: Digi International/Maxstream
文件页数: 26/71页
文件大小: 0K
描述: ANT 900MHZ 6" R/A JOINT W/RPSMA
标准包装: 25
系列: A09-HASM
天线类型: 鞭状:1/2 波,直角
频带数目: 1
频率: 915MHz(902MHz ~ 928MHz)
增益: 2.1dBi
端子: RP-SMA
安装类型: 连接器
包装: 散装
9XTend? ? OEM ? RF ? Module ?‐? Product ? Manual ? v2.x4x ? [2007.01.04]
DT (Destination Address) Command
<Networking & Security> DT Command is used to
set/read the networking address of an RF module.
The modules utilize three filtration layers: Vendor
ID Number (ATID), Channel (ATHP), and Destina-
tion Address (ATDT). The DT command assigns an
address to a module that enables it to communi-
cate only with other modules having the same
address. All modules that share the same DT
parameter can communicate with each other.
Chapter ? 3 ?‐? RF ? Module ? Configuration
AT Command: ATDT
Binary Command: 0x00
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: HP (Hopping Channel), ID
(Modem VID), MK (Address Mask), MY (Source
Address)
RF modules in the same network with a different
destination address (than that of the transmitter) will listen to all transmissions to stay synchro-
nized, but will not send any of the data out their serial ports.
Refer to the ‘Addressing’ section [p44] for more information.
E0 (Echo Off) Command
<Command Mode Options> E0 Command turns
off character echo in AT Command Mode.
By default, echo is off.
E1 (Echo On) Command
<Command Mode Options> E1 Command enables
character echo in AT Command Mode. Each typed
character will be echoed back to the terminal
when ATE1 is active. E0 (Echo Off) is the default.
ER (Receive Error Count) Command
<Diagnostics> The ER command is used to set/
read the number of receive-errors. The error
count records the number of packets partially
received then aborted on a reception error. This
value returns to 0 after a reset and is not non-
volatile (Value does not persist in the module's
memory after a power-up sequence). Once the
Receive Error Count reaches its maximum value
AT Command: ATE0
Binary Command: 0x0A (10 decimal)
AT Command: ATE1
Binary Command: 0x0B (11 decimal)
AT Command: ATER
Binary Command: 0x0F (15 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: GD (Receive Good Count)
(up to 0xFFFF), it remains at its maximum count
value until the maximum count value is explicitly changed or the module is reset.
The ER parameter is not reset by pin, serial port or cyclic sleep modes.
FH (Force Wake-up Initializer) Command
<Sleep (Low Power)> The FH command is used
to force a Wake-up Initializer to be sent on the
next transmission. Use only with cyclic sleep
AT Command: ATFH
Binary Command: 0x0D (13 decimal)
modes active on remote modules.
ATFH will not send a long header if ATHT = 0xFFFF. WR (Write) Command does not need to be
issued with FH Command.
? ? 2007 ? MaxStream, ? Inc.
????? 26
相关PDF资料
PDF描述
A09-HSM-7 ANT 900MHZ 7" STRAIGHT W/RPSMA
US5881LUA-AAA-000-BU IC HALL EFFECT SW MP TO-92UA
F1827SD600 MODULE SCR/DIODE 25A 240VAC
US2881EUA-AAA-000-BU IC LATCH CMOS H-SEN TO-92UA
US4881LUA-AAA-000-BU IC LATCH CMOS H-S TO-92UA
相关代理商/技术参数
参数描述
A09-HASM-7 功能描述:ANT HALF WAVE 900MHZ 6" RPSMA M RoHS:是 类别:RF/IF 和 RFID >> RF 天线 系列:- 标准包装:1 系列:*
A09-HBMM-P5I 功能描述:天线 900Mhz 天线 MMCX w/5" pigtail cable RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HBSM-P5I 功能描述:天线 915MHz 915MHz7" half unt RPSMA connector RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HSM-7 功能描述:天线 915MHz 915MHz6" half Bi non-articulating RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HTM-675 功能描述:天线 915MHz 915MHz6" half Bi straight antenna RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W