参数资料
型号: A09-HASM-675
厂商: Digi International/Maxstream
文件页数: 35/71页
文件大小: 0K
描述: ANT 900MHZ 6" R/A JOINT W/RPSMA
标准包装: 25
系列: A09-HASM
天线类型: 鞭状:1/2 波,直角
频带数目: 1
频率: 915MHz(902MHz ~ 928MHz)
增益: 2.1dBi
端子: RP-SMA
安装类型: 连接器
包装: 散装
9XTend? ? OEM ? RF ? Module ?‐? Product ? Manual ? v2.x4x ? [2007.01.04]
RP (RSSI PWM Timer) Command
<Diagnostics> RP Command is used to enable a
PWM ("Pulse Width Modulation") output on the
Config/RSSI pin (pin 11 of the OEM RF Module).
The pin is calibrated to show the difference
between received signal strength and the sensi-
tivity level of the RF module. PWM pulses vary
from zero to 95 percent. Zero percent means the
received RF signal is at or below the published
Chapter ? 3 ?‐? RF ? Module ? Configuration
AT Command: ATRP
Binary Command: 0x22 (34 decimal)
Parameter Range: 0 - 0xFF
[x 100 milliseconds]
Default Parameter Value: 0x20 (32d)
Number of bytes returned: 1
sensitivity level of the module.
The following table shows dB levels above sensitivity and PWM values (The total time period of the
PWM output is 8.32 ms. PWM output consists of 40 steps and therefore the minimum step size is
0.208 ms.):
Table ? 3 ‐ 02.
PWM ? Values
dBm above sensitivity
10
20
30
PWM percentage
(high period / total period)
20%
35%
50%
A non-zero value defines the time that PWM output is active with the RSSI value of the last
received RF packet. After the set time when no RF packets are received, PWM output is set low (0
percent PWM) until another RF packet is received. PWM output is also set low at power-up. A
parameter value of 0xFF permanently enables PWM output and always reflects the value of the last
received RF packet.
The Config/RSSI pin is shared between PWM output and Config input. When the module is pow-
ered, the Config pin is an input. During the power-up sequence, if RP parameter is a non-zero
value, the Config pin is configured as an output and set low until the first RF packet is received.
With a non-zero RP parameter, the Config pin is an input for RP ms after power up.
RR (Retries) Command
<Networking & Security> The RR command is
used to set/read the maximum number of retries
sent for a given RF packet. When RR Command is
enabled (RR>0), RF packet retries and ACKs
(acknowledgements) are enabled.
Exceptions: If the MT command in enabled
(MT>0) or if a broadcast Destination Address is
AT Command: ATRR
Binary Command: 0x18 (24 decimal)
Parameter Range: 0 - 0xFF
Default Parameter Value: 0x0A (10 decimal)
Number of bytes returned: 1
used (DT = 0xFFFF); RF packet retries and ACKs are disabled.
After transmitting a packet, the transmitting RF module waits to receive an acknowledgement
from a receiving module. If the acknowledgement is not received in the period of time specified by
RN (Delay Slots) Command, the original packet is transmitted again. The RF packet is transmitted
repeatedly until an acknowledgement is received or until the packet is sent RR times.
? ? 2007 ? MaxStream, ? Inc.
????? 35
相关PDF资料
PDF描述
A09-HSM-7 ANT 900MHZ 7" STRAIGHT W/RPSMA
US5881LUA-AAA-000-BU IC HALL EFFECT SW MP TO-92UA
F1827SD600 MODULE SCR/DIODE 25A 240VAC
US2881EUA-AAA-000-BU IC LATCH CMOS H-SEN TO-92UA
US4881LUA-AAA-000-BU IC LATCH CMOS H-S TO-92UA
相关代理商/技术参数
参数描述
A09-HASM-7 功能描述:ANT HALF WAVE 900MHZ 6" RPSMA M RoHS:是 类别:RF/IF 和 RFID >> RF 天线 系列:- 标准包装:1 系列:*
A09-HBMM-P5I 功能描述:天线 900Mhz 天线 MMCX w/5" pigtail cable RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HBSM-P5I 功能描述:天线 915MHz 915MHz7" half unt RPSMA connector RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HSM-7 功能描述:天线 915MHz 915MHz6" half Bi non-articulating RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HTM-675 功能描述:天线 915MHz 915MHz6" half Bi straight antenna RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W