参数资料
型号: A09-HASM-675
厂商: Digi International/Maxstream
文件页数: 27/71页
文件大小: 0K
描述: ANT 900MHZ 6" R/A JOINT W/RPSMA
标准包装: 25
系列: A09-HASM
天线类型: 鞭状:1/2 波,直角
频带数目: 1
频率: 915MHz(902MHz ~ 928MHz)
增益: 2.1dBi
端子: RP-SMA
安装类型: 连接器
包装: 散装
9XTend? ? OEM ? RF ? Module ?‐? Product ? Manual ? v2.x4x ? [2007.01.04]
FL (Software Flow Control) Command
<Serial Interfacing> The FL command is used to
configure software flow control. Hardware flow
control is implemented with the module as the
GP01 pin (CTS pin of the OEM RF module), which
Chapter ? 3 ?‐? RF ? Module ? Configuration
AT Command: ATFL
Binary Command: 0x07 (7 decimal)
Parameter Range: 0 - 1
regulates when serial data can be transferred to
the module.
FL Command can be used to allow software flow
Parameter
0
Configuration
Disable software
flow control
1
control to also be enabled. The XON character
used is 0x11 (17 decimal). The XOFF character
used is 0x13 (19 decimal)
Enable software
flow control
Default Parameter Value: 0
Number of bytes returned: 1
FS (Forced Synch Time) Command
<RF Interfacing> The FS command only applies
to streaming data. Normally, only the first packet
of a continuous stream contains the full RF initial-
izer. The RF modules then remain synchronized
for subsequent packets of the stream. This
parameter can be used to periodically force an RF
initializer during such streaming. Any break in
UART character reception long enough to drain
AT Command: ATFS
Binary Command: 0x3E (62 decimal)
Parameter Range: 0 - 0xFFFF
[x 10 milliseconds]
Default Parameter Value: 0
Number of bytes returned: 2
the DI Buffer (UART receive buffer) and cause a pause in RF data transmission will also cause an
RF initializer to be inserted on the next transmission.
FT (Flow Control Threshold) Command
<Serial Interfacing> The FT command is used to
set/read the flow control threshold. When FT
bytes have accumulated in the DI buffer (UART
Receive), CTS is de-asserted or the XOFF soft-
ware flow control character is transmitted.
AT Command: ATFT
Binary Command: 0x24 (36 decimal)
Parameter Range:
0 - (DI buffer size minus 0x11) [Bytes]
Default Parameter Value: DI Buffer size minus
0x11 (17 decimal)
Number of bytes returned: 2
GD (Receive Good Count) Command
<Diagnostics> The GD command is used to set/
read the count of good received RF packets. Its
parameter value is reset to 0 after every reset
and is not non-volatile (The parameter value does
not persist in the RF module's memory after a
power-up sequence). Once the "Receive Good
Count" reaches its maximum value (up to
0xFFFF), it remains at its maximum count value
AT Command: ATGD
Binary Command: 0x10 (16 decimal)
Parameter Range: 0 - 0xFFFF
Default Parameter Value: 0
Number of bytes returned: 2
Related Commands: ER (Receive Error Count)
until the maximum count value is manually
changed or the module is reset.
The GD parameter is not reset by pin, serial port or cyclic sleep modes.
? ? 2007 ? MaxStream, ? Inc.
????? 27
相关PDF资料
PDF描述
A09-HSM-7 ANT 900MHZ 7" STRAIGHT W/RPSMA
US5881LUA-AAA-000-BU IC HALL EFFECT SW MP TO-92UA
F1827SD600 MODULE SCR/DIODE 25A 240VAC
US2881EUA-AAA-000-BU IC LATCH CMOS H-SEN TO-92UA
US4881LUA-AAA-000-BU IC LATCH CMOS H-S TO-92UA
相关代理商/技术参数
参数描述
A09-HASM-7 功能描述:ANT HALF WAVE 900MHZ 6" RPSMA M RoHS:是 类别:RF/IF 和 RFID >> RF 天线 系列:- 标准包装:1 系列:*
A09-HBMM-P5I 功能描述:天线 900Mhz 天线 MMCX w/5" pigtail cable RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HBSM-P5I 功能描述:天线 915MHz 915MHz7" half unt RPSMA connector RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HSM-7 功能描述:天线 915MHz 915MHz6" half Bi non-articulating RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W
A09-HTM-675 功能描述:天线 915MHz 915MHz6" half Bi straight antenna RoHS:否 制造商:Molex 技术类型:Cellular Antenna 频率: 带宽: 尺寸:106.7 mm L x 13 mm W