- 您现在的位置：买卖IC网 > PDF目录164964 > A1361LKTTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT PDF资料下载
参数资料
| 型号： | A1361LKTTN-T |
| 元件分类： | 磁阻传感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 4.65-4.80V, RECTANGULAR, THROUGH HOLE MOUNT |
| 封装： | LEAD FREE, PLASTIC, SIP-4 |
| 文件页数： | 11/25页 |
| 文件大小： | 615K |
| 代理商： | A1361LKTTN-T |
A1360, A1361,
and A1362
Figure 6. Pulses to enter Try mode, zone 2. Example shown is
for addressing the Fine Quiescent Voltage Output register. After
addressing desired code, cycle the supply to reset the bit field or apply
a blow pulse to make the parameter value permanent.
Blow Mode
After the required value of the programmable parameter is
addressed using Try mode, its corresponding code can be blown
to make its value permanent. To do this, select the required
parameter register and the appropriate code. (See the Fuse Blow-
ing section. Recall that each bit of a desired code must be blown
individually before cycling the supply.) If the desired parameter
is in the first zone, enter the appropriate key-code combination
and then apply two high-level voltage pulses followed by an
additional blow pulse. If the desired parameter is in the second
zone, enter the appropriate key-code combination and then apply
a single blow pulse on the VOUT pin. This is diagrammed as
follows:
Zone 1: VPH → Key → VPH → Code for Single Bit → VPH →
VPH → VPH
Zone 2: VPH → VPH → VPH → Key → VPH → Code for
Single Bit → VPH
Note: During a single blowing sequence, only one programmable
parameter in a single zone should be set at a time. After each
blow sequence the supply should be cycled before attempting to
blow additional bits.
Lock Mode
To lock the device, address the LOCK bit and apply a blow pulse
with CBLOW in place. The LOCK bit is located in zone 2, register
2, code 4. After locking the device, no future programming of any
parameter is possible.
The lock sequence is:
VPH → VPH → VPH → VPM → VPM →VPH → VPM → VPM
→ VPM → VPM → VPH
Low-Noise Programmable Linear Hall Effect Sensor ICs with
Adjustable Bandwidth (50 kHz Maximum) and Analog Output
19
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A150N50X4A | 0 MHz - 2700 MHz 50 ohm RF/MICROWAVE TERMINATION |
| A15QS1-2 | FAST BLOW ELECTRIC FUSE, 1A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS10-2 | FAST BLOW ELECTRIC FUSE, 10A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4TI | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
| A15QS100-4 | FAST BLOW ELECTRIC FUSE, 100A, 150VAC, 150VDC, 100000A (IR), INLINE/HOLDER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A1362LKTTN-T | 功能描述:IC HALL EFFECT SENSOR LN 4-SIP RoHS:是 类别:传感器，转换器 >> 磁性 - 霍尔效应，数字式开关，线性，罗盘 (IC) 系列:- 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出（最大）:- 输出类型:数字式，PWM，8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP（0.209"，5.30mm 宽） 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR |
| A1363LKTTN-10-T | 功能描述:IC HALL SENSOR 6.4-14MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 类型:线性 技术:霍尔效应 轴:单路 感应范围:- 电压 - 电源:4.5 V ~ 5.5 V 电流 - 电源（最大值）:15mA 电流 - 输出（最大值）:10mA 输出类型:模拟电压 分辨率:- 带宽:120kHz 工作温度:-40°C ~ 150°C（TA） 特性:可编程，温度补偿 封装/外壳:4-SIP 模块 供应商器件封装:4-SIP 标准包装:1 |
| A1363LKTTN-1-T | 功能描述:IC HALL SENSOR 0.6-1.3MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 类型:线性 技术:霍尔效应 轴:单路 感应范围:- 电压 - 电源:4.5 V ~ 5.5 V 电流 - 电源（最大值）:15mA 电流 - 输出（最大值）:10mA 输出类型:模拟电压 分辨率:- 带宽:120kHz 工作温度:-40°C ~ 150°C（TA） 特性:可编程，温度补偿 封装/外壳:4-SIP 模块 供应商器件封装:模块 标准包装:1 |
| A1363LKTTN-2-T | 功能描述:IC HALL SENSOR 1.3-2.9MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 类型:线性 技术:霍尔效应 轴:单路 感应范围:- 电压 - 电源:4.5 V ~ 5.5 V 电流 - 电源（最大值）:15mA 电流 - 输出（最大值）:10mA 输出类型:模拟电压 分辨率:- 带宽:120kHz 工作温度:-40°C ~ 150°C（TA） 特性:可编程，温度补偿 封装/外壳:4-SIP 模块 供应商器件封装:4-SIP 标准包装:1 |
| A1363LKTTN-5-T | 功能描述:IC HALL SENSOR 2.9-6.4MV/G 4SIP 制造商:allegro microsystems, llc 系列:- 包装:剪切带（CT） 零件状态:有效 类型:线性 技术:霍尔效应 轴:单路 感应范围:- 电压 - 电源:4.5 V ~ 5.5 V 电流 - 电源（最大值）:15mA 电流 - 输出（最大值）:10mA 输出类型:模拟电压 分辨率:- 带宽:120kHz 工作温度:-40°C ~ 150°C（TA） 特性:可编程，温度补偿 封装/外壳:4-SIP 模块 供应商器件封装:4-SIP 标准包装:1 |
发布紧急采购，3分钟左右您将得到回复。