- 您现在的位置：买卖IC网 > Datasheet目录306 > A4933KJPTR-T (Allegro Microsystems Inc)IC PREDRIVER MOSFET 3PH 48LQFP Datasheet资料下载
参数资料
| 型号： | A4933KJPTR-T |
| 厂商： | Allegro Microsystems Inc |
| 文件页数： | 18/25页 |
| 文件大小： | 0K |
| 描述： | IC PREDRIVER MOSFET 3PH 48LQFP |
| 标准包装： | 4,500 |
| 配置： | 3 相桥 |
| 输入类型： | PWM |
| 延迟时间： | 90ns |
| 配置数： | 1 |
| 输出数： | 3 |
| 电源电压： | 5.5 V ~ 50 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP 裸露焊盘 |
| 供应商设备封装： | 48-LQFP |
| 包装： | 带卷 (TR) |
A4933
Automotive 3-Phase MOSFET Driver
is set to zero by connecting RDEAD to AGND, the fault blank
time typically defaults to 2 μ s.
The voltage drop across the bootstrap capacitor as the FET is
being turned on, ? V , can be approximated by:
Cross-Conduction
? V ≈
Q GATE
C BOOT
.
(4)
In some circumstances it is desirable to allow activation of both
high-side and low-side FETs in a single phase of the power
bridge. This can be used, with care, to reduce diode conduction
during synchronous rectification, which improves overall effi-
ciency and reduces electromagnetic emissions.
This mode of operation is also useful for independently control-
ling each phase of a VR motor or to turn on all high-side and low-
side FETs together, to cause a supply short circuit for blowing a
safety fuse.
Cross-conduction can occur only when the internally-generated
dead time is set to zero by connecting RDEAD to AGND and, at
the same time, CCEN is high. If zero internally-generated dead
time is required, but cross-conduction is to be prevented, then
CCEN can be tied to AGND. When the dead time is set to zero
So, for a factor of 20, ? V would be approximately 5% of V BOOT .
The maximum voltage across the bootstrap capacitor under
normal operating conditions is V REG (max). However, in some
circumstances the voltage may transiently reach 18 V, the clamp
voltage of the Zener diodes between the Cx and Sx pins. In most
applications, with a good ceramic capacitor the working voltage
can be limited to 16 V.
Bootstrap Charging
It is good practice to ensure the high-side bootstrap capacitor is
completely charged before a high-side PWM cycle is requested.
The time required to charge the capacitor, t CHARGE ( μ s), is
approximated by:
it is still possible for some overlap to be present at the switching
instants due to the relative switching time of the FETs.
t CHARGE =
C BOOT × ? V
500
,
(5)
Bootstrap Capacitor Selection
The bootstrap capacitors, C BOOTx , must be correctly selected to
ensure proper operation of the A4933. If the capacitances are too
high, time will be wasted charging the capacitor, resulting in a
limit on the maximum duty cycle and the PWM frequency. If the
capacitances are too low, there can be a large voltage drop at the
time the charge is transferred from C BOOTx to the FET gate, due
to charge sharing.
To keep this voltage drop small, the charge in the bootstrap
capacitor, Q BOOT , should be much larger than the charge required
by the gate of the FET, Q GATE . A factor of 20 is a reasonable
value, and the following formula can be used to calculate the
value for C BOOT :
where C BOOT is the value of the bootstrap capacitor, in nF, and
? V is the required voltage of the bootstrap capacitor.
At power-up and when the drives have been disabled for a long
time, the bootstrap capacitor can be completely discharged. In
this case ? V can be considered to be the full high-side drive
voltage, 12 V. Otherwise, ? V is the amount of voltage dropped
during the charge transfer, which should be 400 mV or less.
The capacitor is charged whenever the Sx pin is pulled low and
current flows from VREG through the internal bootstrap diode
circuit to C BOOT .
Bootstrap Charge Management
The A4933 provides automatic bootstrap capacitor charge
management. The bootstrap capacitor voltage for each phase
Q BOOT = C BOOT × V BOOT = Q GATE × 20 ,
therefore:
Q GATE × 20
C BOOT = ,
V BOOT
where V BOOT is the voltage across the bootstrap capacitor.
(3)
is continuously checked to ensure that it is above the bootstrap
under-voltage threshold, V BOOTUV . If the bootstrap capacitor volt-
age drops below this threshold, the A4933 will turn on the neces-
sary low-side FET, and continue charging until the bootstrap
capacitor exceeds the undervoltage threshold plus the hysteresis,
V BOOTUV + V BOOTUVhys . The minimum charge time is typically
7 μ s, but may be longer for very large values of bootstrap capaci-
18
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
相关PDF资料 |
PDF描述 |
|---|---|
| A4935KJPTR-T | IC MOSFET DVR AUTO 3PH 48-LQFP |
| A4940KLPTR-T | IC MOSF DVR FULL BRIDGE 24TSSOP |
| A6210GEUTR-T | IC LED DRIVER HIGH BRIGHT 16-QFN |
| A6261KLPTR-T | IC LED ARRAY DVR 400MA 16-TSSOP |
| A6262KLPTR-T | IC LED ARRAY DRIVER AUTO 16TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| A4934GLPTR-T | 功能描述:IC BLDC DVR 3PHASE 16-ETSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 电机和风扇控制器，驱动器 系列:- 标准包装:1 系列:- 应用:直流电机驱动器，步进电机驱动器 评估套件:- 输出数:1 或 2 电流 - 输出:750mA 电压 - 负载:10 V ~ 40 V 电源电压:4.5 V ~ 5.5 V 工作温度:-20°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-BFSOP（0.295"，7.50mm 宽） 供应商设备封装:24-SOP 包装:Digi-Reel® 其它名称:MTS62C19A-HS105DKR |
| A4935 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive 3-Phase MOSFET Driver |
| A4935_12 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:The A4935 is a 3-phase controller for use with N-channel external power MOSFETs and is specifically designed for automotive applications. |
| A4935_13 | 制造商:ALLEGRO 制造商全称:Allegro MicroSystems 功能描述:Automotive 3-Phase MOSFET Driver |
| A4935KJP-T | 功能描述:IC MOSFET DRIVER 3PH AUTO 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:- 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
发布紧急采购，3分钟左右您将得到回复。