参数资料
| 型号： | AD5363BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/29页 |
| 文件大小： | 0K |
| 描述： | IC DAC 14BIT 8CH SERIAL 56-LFCSP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 1 |
| 设置时间： | 20µs |
| 位数： | 14 |
| 数据接口： | 串行 |
| 转换器数目： | 8 |
| 电压电源： | 双 ± |
| 功率耗散（最大）： | 209mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 56-LFCSP-VQ（8x8） |
| 包装： | 托盘 |
| 输出数目和类型： | 8 电压，单极；8 电压，双极 |
| 采样率（每秒）： | * |
| 配用： | EVAL-AD5363EBZ-ND - BOARD EVALUATION FOR AD5363 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
AD5362/AD5363
Rev. A | Page 17 of
28
A/B REGISTERS AND GAIN/OFFSET ADJUSTMENT
Each DAC channel has seven data registers. The actual DAC
data-word can be written to either the X1A or X1B input
register, depending on the setting of the A/B bit in the control
register. If the A/B bit is 0, data is written to the X1A register.
If the A/B bit is 1, data is written to the X1B register. Note that
this single bit is a global control and affects every DAC channel
in the device. It is not possible to set up the device on a per-
channel basis so that some writes are to X1A registers and some
writes are to X1B registers.
MUX
DAC
REGISTER
MUX
X1A
REGISTER
X1B
REGISTER
M
REGISTER
C
REGISTER
X2A
REGISTER
X2B
REGISTER
05
76
2-
0
20
Figure 21. Data Registers Associated with Each DAC Channel
Each DAC channel also has a gain (M) register and an offset (C)
register, which allow trimming out of the gain and offset errors
of the entire signal chain. Data from the X1A register is operated
on by a digital multiplier and adder controlled by the contents of
the M and C registers. The calibrated DAC data is then stored in
the X2A register. Similarly, data from the X1B register is operated
on by the multiplier and adder and stored in the X2B register.
Although a multiplier and an adder symbol are shown in Figure 21
for each channel, there is only one multiplier and one adder in
the device, which are shared among all channels. This has impli-
cations for the update speed when several channels are updated
at once, as described in the Register Update Rates section.
Each time data is written to the X1A register, or to the M or C
register with the A/B control bit set to 0, the X2A data is recal-
culated and the X2A register is automatically updated. Similarly,
X2B is updated each time data is written to X1B, or to M or C
with A/B set to 1. The X2A and X2B registers are not readable
or directly writable by the user.
Data output from the X2A and X2B registers is routed to the
final DAC register by a multiplexer. A 4-bit A/B select register
associated with each group of four DACs controls whether each
individual DAC takes its data from the X2A or X2B register. If a
bit in this register is 0, the DAC takes its data from the X2A
register; if 1, the DAC takes its data from the X2B register.
Note that because there are eight bits in two registers, it is possible
to set up, on a per-channel basis, whether each DAC takes its
data from the X2A or X2B register. A global command is also
provided that sets all bits in the A/B select registers to 0 or to 1.
All DACs in the AD5362/AD5363 can be updated simultane-
ously by taking LDAC low when each DAC register is updated
from either its X2A or X2B register, depending on the setting of
the A/B select registers. The DAC register is not readable or
directly writable by the user. LDAC can be permanently tied
low, and the DAC output is updated whenever new data appears
in the appropriate DAC register.
OFFSET DACS
In addition to the gain and offset trim for each DAC, there are
two 14-bit offset DACs, one for Group 0 and one for Group 1.
These allow the output range of all DACs connected to them to
be offset within a defined range. Thus, subject to the limitations
of headroom, it is possible to set the output range of Group 0 or
Group 1 to be unipolar positive, unipolar negative, or bipolar,
either symmetrical or asymmetrical about 0 V. The DACs in the
AD5362/AD5363 are factory trimmed with the offset DACs set
at their default values. This gives the best offset and gain perfor-
mance for the default output range and span.
When the output range is adjusted by changing the value of the
offset DAC, an extra offset is introduced due to the gain error of
the offset DAC. The amount of offset is dependent on the mag-
nitude of the reference and how much the offset DAC moves
from its default value. See the Specifications section for this
offset. The worst-case offset occurs when the offset DAC is at
positive or negative full scale. This value can be added to the
offset present in the main DAC channel to give an indication of
the overall offset for that channel. In most cases, the offset can
be removed by programming the C register of the channel with
an appropriate value. The extra offset caused by the offset DAC
needs to be taken into account only when the offset DAC is
changed from its default value. Figure 22 shows the allowable
code range that can be loaded to the offset DAC, depending on
the reference value used. Thus, for a 5 V reference, the offset
DAC should not be programmed with a value greater than 8192
(0x2000).
0
4096
8192
12288
16383
OFFSET DAC CODE
0
1
2
3
4
V
R
E
F
(V
)
5
RESERVED
0
57
62
-02
1
Figure 22. Offset DAC Code Range
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1596AISW#TRPBF | IC D/A CONV 16BIT MLTPLYNG16SOIC |
| LTC1596AISW#TR | IC DAC 16BIT MULTIPLY SER 16SOIC |
| LTC1596-1AISW#TRPBF | IC D/A CONV 16BIT MLTPLYNG16SOIC |
| LTC1596-1AISW#TR | IC DAC 16BIT MULTIPLY SER 16SOIC |
| AD7237AAN | IC DAC 12BIT W/AMP W/BUFF 24-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5363BCPZ-REEL7 | 功能描述:IC DAC 14BIT 8CH SERIAL 56-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5363BSTZ | 功能描述:IC DAC 14BIT 8CH SERIAL 52-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5363BSTZ-REEL | 功能描述:IC DAC 14BIT 8CH SERIAL 52-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5365D/BIN/883B | 制造商:Analog Devices 功能描述:- Rail/Tube |
| AD536A | 制造商:AD 制造商全称:Analog Devices 功能描述:Integrated Circuit True RMS-to-DC Converter |
发布紧急采购，3分钟左右您将得到回复。