参数资料
| 型号： | AD5755-1ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/52页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SERIAL 64LFCSP |
| 视频文件： | AD5755: 16-Bit Multi-Channel, Voltage and Current Output DAC |
| 特色产品： | AD5755 / AD5755-1 / AD5757 DACs |
| 标准包装： | 1 |
| 设置时间： | 11µs |
| 位数： | 16 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 模拟和数字，双 ± |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 托盘 |
| 输出数目和类型： | 4 电流，4 电压 |
| 采样率（每秒）： | * |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
AD5755-1
Data Sheet
Rev. E | Page 32 of 52
PROGRAMMING SEQUENCE TO WRITE/ENABLE
THE OUTPUT CORRECTLY
To correctly write to and set up the part from a power-on
condition, use the following sequence:
1. Perform a hardware or software reset after initial power-on.
2. The dc-to-dc converter supply block must be configured.
Set the dc-to-dc switching frequency, maximum output
voltage allowed, and the phase that the four dc-to-dc
channels clock at.
3. Configure the DAC control register on a per channel basis.
The output range is selected, and the dc-to-dc converter
block is enabled (DC_DC bit). Other control bits can be
configured at this point. Set the INT_ENABLE bit; however,
the output enable bit (OUTEN) should not be set.
4. Write the required code to the DAC data register. This
implements a full DAC calibration internally. Allow at least
200 s before Step 5 for reduced output glitch.
5. Write to the DAC control register again to enable the
output (set the OUTEN bit).
A flowchart of this sequence is shown in Figure 75.
09226-
073
POWER ON.
STEP 1: PERFORM A SOFTWARE/HARDWARE RESET.
STEP 4: WRITE TO EACH/ALL DAC DATA REGISTERS.
ALLOW AT LEAST 200s BETWEEN STEP 3
AND STEP 5 FOR REDUCED OUTPUT GLITCH.
STEP 2: WRITE TO DC-TO-DC CONTROL REGISTER TO
SET DC-TO-DC CLOCK FREQUENCY, PHASE,
AND MAXIMUM VOLTAGE.
STEP 3: WRITE TO DAC CONTROL REGISTER. SELECT
THE DAC CHANNEL AND OUTPUT RANGE.
SET THE DC_DC BIT AND OTHER CONTROL
BITS AS REQUIRED. SET THE INT_ENABLE BIT
BUT DO NOT SELECT THE OUTEN BIT.
STEP 5: WRITE TO DAC CONTROL REGISTER. RELOAD
SEQUENCE AS IN STEP 3 ABOVE. THIS TIME
SELECT THE OUTEN BIT TO ENABLE
THE OUTPUT.
Figure 75. Programming Sequence for Enabling the Output Correctly
CHANGING AND REPROGRAMMING THE RANGE
When changing between ranges, the same sequence as
described in the Programming Sequence to Write/Enable the
Output Correctly section should be used. It is recommended to
set the range to its zero point (can be midscale or zero scale)
prior to disabling the output. Because the dc-to-dc switching
frequency, maximum voltage, and phase have already been
selected, there is no need to reprogram these. A flowchart of
this sequence is shown in Figure 76.
09226-
074
CHANNEL’S OUTPUT IS ENABLED.
STEP 3: WRITE VALUE TO THE DAC DATA REGISTER.
STEP 1: WRITE TO CHANNEL’S DAC DATA
REGISTER. SET THE OUTPUT
TO 0V (ZERO OR MIDSCALE).
STEP 2: WRITE TO DAC CONTROL REGISTER.
DISABLE THE OUTPUT (OUTEN = 0), AND
SET THE NEW OUTPUT RANGE. KEEP THE
DC_DC BIT AND THE INT_ENABLE BIT SET.
STEP 4: WRITE TO DAC CONTROL REGISTER.
RELOAD SEQUENCE AS IN STEP 2 ABOVE.
THIS TIME SELECT THE OUTEN BIT TO
ENABLE THE OUTPUT.
Figure 76. Steps for Changing the Output Range
相关PDF资料 |
PDF描述 |
|---|---|
| AD5755BCPZ-REEL7 | IC DAC 16BIT QUAD 64-LFCSP |
| AD5760BCPZ | IC DAC VOLT OUT 16BIT 24LFCSP |
| AD5762RCSUZ-REEL7 | IC DAC 16BIT QUAD VOUT 32-TQFP |
| AD5763CSUZ-REEL7 | DAC 16BIT DUAL 5V 2LSB 32-TQFP |
| AD5764CSUZ | IC DAC 16BIT QUAD VOUT 32TQFP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5755-1ACPZ-REEL7 | 功能描述:IC DAC 16BIT SERIAL 64LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Data Converter Fundamentals DAC Architectures 标准包装:750 系列:- 设置时间:7µs 位数:16 数据接口:并联 转换器数目:1 电压电源:双 ± 功率耗散（最大）:100mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-LCC（J 形引线） 供应商设备封装:28-PLCC（11.51x11.51） 包装:带卷 (TR) 输出数目和类型:1 电压，单极；1 电压，双极 采样率（每秒）:143k |
| AD5755-1X | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad Channel, 16-Bit, Serial Input, 4-20mA & Voltage Output DAC, Dynamic Power Control, HART Connectivity |
| AD5755ACPZ | 功能描述:数模转换器- DAC 16Bit Quad V/I DAC with Dynamic Power RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| AD5755ACPZ-REEL7 | 功能描述:IC DAC 16BIT QUAD 64-LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD5755BCPZ | 制造商:Analog Devices 功能描述: 制造商:Analog Devices 功能描述:DAC QUAD 16BIT -26.4/33VIN 64LFCSP 制造商:Analog Devices 功能描述:DAC, QUAD, 16BIT, -26.4/33VIN, 64LFCSP 制造商:Analog Devices 功能描述:DAC, QUAD, 16BIT, -26.4/33VIN, 64LFCSP, Resolution (Bits):16bit, Input Channel Type:Serial, Digital IC Case Style:LFCSP, No. of Pins:64, Data Interface:Microwire, QSPI, SPI, Supply Current:8.6mA, Operating Temperature Min:-40C, , RoHS Compliant: Yes |
发布紧急采购，3分钟左右您将得到回复。