- 您现在的位置：买卖IC网 > PDF目录1891 > AD5930YRUZ-REEL7 (Analog Devices Inc)IC GEN PROG FREQ BURST 20TSSOP PDF资料下载
参数资料
| 型号： | AD5930YRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 15/28页 |
| 文件大小： | 0K |
| 描述： | IC GEN PROG FREQ BURST 20TSSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 1,000 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 50MHz |
| 调节字宽（位）： | 24 b |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD5930
Data Sheet
Rev. B | Page 22 of 28
APPLICATIONS
GROUNDING AND LAYOUT
The printed circuit board that houses the AD5930 should be
designed so that the analog and digital sections are separated
and confined to certain areas of the board. This facilitates the
use of ground planes that can be easily separated. A minimum
etch technique is generally best for ground planes because it
gives the best shielding. Digital and analog ground planes
should only be joined in one place. If the AD5930 is the only
device requiring an AGND to DGND connection, then the
ground planes should be connected at the AGND and DGND
pins of the AD5930. If the AD5930 is in a system where
multiple devices require AGND to DGND connections, the
connection should be made at one point only, a star ground
point that should be established as close as possible to the
AD5930.
Avoid running digital lines under the device as these couple
noise onto the die. The analog ground plane should be allowed
to run under the AD5930 to avoid noise coupling. The power
supply lines to the AD5930 should use as large a track as
possible to provide low impedance paths and reduce the effects
of glitches on the power supply line. Fast switching signals, such
as clocks, should be shielded with digital ground to avoid
radiating noise to other sections of the board. Avoid crossover
of digital and analog signals. Traces on opposite sides of the
board should run at right angles to each other. This reduces the
effects of feedthrough through the board. A microstrip
technique is by far the best, but is not always possible with a
double-sided board. In this technique, the component side of
the board is dedicated to ground planes, while signals are placed
on the other side.
Good decoupling is important. The analog and digital supplies
to the AD5930 are independent and separately pinned out to
minimize coupling between analog and digital sections of the
device. All analog and digital supplies should be decoupled to
AGND and DGND, respectively, with 0.1 μF ceramic capacitors
in parallel with 10 μF tantalum capacitors. To achieve the best
from the decoupling capacitors, they should be placed as close
as possible to the device, ideally right up against the device. In
systems where a common supply is used to drive both the
AVDD and DVDD of the AD5930, it is recommended that the
system’s AVDD supply be used. This supply should have the
recommended analog supply decoupling between the AVDD
pins of the AD5930 and AGND, and the recommended digital
supply decoupling capacitors between the DVDD pins and
DGND.
Proper operation of the comparator requires good layout
strategy. The strategy must minimize the parasitic capacitance
between VIN and the SIGN BIT OUT pin by adding isolation
using a ground plane. For example, in a multilayered board, the
VIN signal could be connected to the top layer and the SIGN
BIT OUT connected to the bottom layer, so that isolation is
provided between the power and ground planes.
Interfacing to Microprocessors
The AD5930 has a standard serial interface that allows the part
to interface directly with several microprocessors. The device
uses an external serial clock to write the data/control
information into the device. The serial clock can have a
frequency of 40 MHz maximum. The serial clock can be
continuous, or it can idle high or low between write operations.
When data/control information is being written to the AD5930,
FSYNC is taken low and is held low while the 16 bits of data are
being written into the AD5930. The FSYNC signal frames the
16 bits of information being loaded into the AD5930.
AD5930 TO ADSP-2101 INTERFACE
Figure 36 shows the serial interface between the AD5930 and
the ADSP-2101. The ADSP-2101 should be set up to operate in
the SPORT transmit alternate framing mode (TFSW = 1). The
ADSP-2101 is programmed through the SPORT control register
and should be configured as follows:
1.
Internal clock operation (ISCLK = 1)
2.
Active low framing (INVTFS = 1)
3.
16-bit word length (SLEN = 15)
4.
Internal frame sync signal (ITFS = 1)
5.
Generate a frame sync for each write (TFSR = 1)
Transmission is initiated by writing a word to the Tx register
after the SPORT has been enabled. The data is clocked out on
each rising edge of the serial clock and clocked into the AD5930
on the SCLK falling edge.
AD59301
ADSP-21011
1ADDITIONAL PINS OMITTED FOR CLARITY.
TFS
DT
SCLK
FSYNC
05
33
3-
0
38
SDATA
SCLK
Figure 36. ADSP-2101 to AD5930 Interface
相关PDF资料 |
PDF描述 |
|---|---|
| AD5932YRUZ-REEL7 | IC PROG WAVEFORM GENERAT 16TSSOP |
| AD5933YRSZ-REEL7 | NETWORK ANALYZER 12B 1MSP 16SSOP |
| AD5934YRSZ | IC NTWK ANALYZER 12B 1MSP 16SSOP |
| AD598JR | IC LVDT SGNL COND OSC/REF 20SOIC |
| AD660BR | IC DAC 16BIT MONO W/VREF 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5932 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Frequency Scan Waveform Generator |
| AD5932YRUZ | 功能描述:IC PROG WAVEFORM GEN SNGL16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5932YRUZ-REEL7 | 功能描述:IC PROG WAVEFORM GENERAT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5933 | 制造商:AD 制造商全称:Analog Devices 功能描述:1 MSPS 12-Bit Impedance Converter, Network Analyzer |
| AD5933BRSZ-U1 | 制造商:Analog Devices 功能描述:CNVRTR NETWORK ANALYZER 16SSOP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。