- 您现在的位置：买卖IC网 > PDF目录1891 > AD5930YRUZ-REEL7 (Analog Devices Inc)IC GEN PROG FREQ BURST 20TSSOP PDF资料下载
参数资料
| 型号： | AD5930YRUZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 8/28页 |
| 文件大小： | 0K |
| 描述： | IC GEN PROG FREQ BURST 20TSSOP |
| 产品培训模块： | Direct Digital Synthesis Tutorial Series (1 of 7): Introduction Direct Digital Synthesizer Tutorial Series (7 of 7): DDS in Action Direct Digital Synthesis Tutorial Series (3 of 7): Angle to Amplitude Converter Direct Digital Synthesis Tutorial Series (6 of 7): SINC Envelope Correction Direct Digital Synthesis Tutorial Series (4 of 7): Digital-to-Analog Converter Direct Digital Synthesis Tutorial Series (2 of 7): The Accumulator |
| 标准包装： | 1,000 |
| 分辨率（位）： | 10 b |
| 主 fclk： | 50MHz |
| 调节字宽（位）： | 24 b |
| 电源电压： | 2.3 V ~ 5.5 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 20-TSSOP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页当前第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD5930
Data Sheet
Rev. | Page 16 of 28
THEORY OF OPERATION
The AD5930 is a general-purpose synthesized waveform
generator capable of providing digitally programmable
waveform sequences in both the frequency and time domain.
The device contains embedded digital processing to provide a
repetitive sweep of a user programmable frequency profile
allowing enhanced frequency control. Because the device is pre-
programmable, it eliminates continuous write cycles from a
DSP/μcontroller in generating a particular waveform.
THE FREQUENCY PROFILE
The frequency profile is defined by the start frequency (FSTART),
the frequency increment (Δf) and the number of increments
per sweep (NINCR). The increment interval between frequency
increments, tINT, is either user programmable with the interval
automatically determined by the device (auto-increment mode),
or externally controlled via a hardware pin (external increment
mode). For automatic update, the interval profile can either be
for a fixed number of clock periods or for a fixed number of
output waveform cycles.
In the auto-increment mode, a single pulse at the CTRL pin starts
and executes the frequency sweep. In the external increment
mode, the CTRL pin also starts the sweep, but the frequency
increment interval is determined by the time interval between
sequential 0/1 transitions on the CTRL pin. Furthermore, the
CTRL pin can be used to directly control the burst profile, where
during the input high time, the output waveform is present, and
during the input low time, the output is reset to midscale.
The frequency profile can be swept in two different modes: saw
sweep or triangular (up/down) sweep.
Saw-Sweep Mode
In the case of a saw sweep, the AD5930 repeatedly
sweeps between sweep start to sweep end, that is, from
FSTART incrementally to
FSTART + NINCR × Δf
This gives a saw-sweep cycle time of
(NINCR + 1) × tINT
FSTART
FSTART + F
FSTART + NINCR × F
MIDSCALE
05333-
009
Figure 31. Saw-Sweep Profile
Triangular-Sweep Mode
In the case of a triangular sweep, the AD5930 repeatedly
sweeps between sweep start to sweep end, that is, from FSTART
incrementally to
FSTART + NINCR × Δf
The triangular-sweep cycle time is given by
(1 + (2 × NINCR)) × tINT
FSTART
05333-
010
FSTART
FSTART + F
FSTART + NINCR × F
MIDSCALE
Figure 32. Triangular-Sweep Profile
OUTPUT MODES
The AD5930 offers two possible output modes: continuous
output mode and burst output mode. Both of these modes are
illustrated in Figure 33.
05333-
0
1
CONTINUOUS
MODE
BURST
MODE
1
2
NUMBER STEP CHANGES
tINT
TBURST
Figure 33. Continuous Mode and Burst Mode of the AD5930
Continuous Output Mode
In this mode, each frequency of the sweep is available for the
length of time programmed into the time interval (tINT) register.
This means the frequency swept output signal is continuously
available, and is therefore phase continuous at all frequency
increments.
To set up the AD5930 in continuous mode, the CW/BURST bit
(D7) in the control register must be set to 0. See the Activating
and Controlling the Sweep section for more details.
Burst Output Mode
In this mode, the AD5930 provides a programmable burst
of the waveform output for a fixed length of time (TBURST)
within the programmed increment interval (tINT). Then for
the remainder of the tINT interval, the output is reset to mid-
scale and remains there until the next frequency increment.
B
相关PDF资料 |
PDF描述 |
|---|---|
| AD5932YRUZ-REEL7 | IC PROG WAVEFORM GENERAT 16TSSOP |
| AD5933YRSZ-REEL7 | NETWORK ANALYZER 12B 1MSP 16SSOP |
| AD5934YRSZ | IC NTWK ANALYZER 12B 1MSP 16SSOP |
| AD598JR | IC LVDT SGNL COND OSC/REF 20SOIC |
| AD660BR | IC DAC 16BIT MONO W/VREF 24-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD5932 | 制造商:AD 制造商全称:Analog Devices 功能描述:Programmable Frequency Scan Waveform Generator |
| AD5932YRUZ | 功能描述:IC PROG WAVEFORM GEN SNGL16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5932YRUZ-REEL7 | 功能描述:IC PROG WAVEFORM GENERAT 16TSSOP RoHS:是 类别:集成电路 (IC) >> 接口 - 直接数字合成 (DDS) 系列:- 产品变化通告:Product Discontinuance 27/Oct/2011 标准包装:2,500 系列:- 分辨率（位）:10 b 主 fclk:25MHz 调节字宽（位）:32 b 电源电压:2.97 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:带卷 (TR) |
| AD5933 | 制造商:AD 制造商全称:Analog Devices 功能描述:1 MSPS 12-Bit Impedance Converter, Network Analyzer |
| AD5933BRSZ-U1 | 制造商:Analog Devices 功能描述:CNVRTR NETWORK ANALYZER 16SSOP - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。