参数资料
| 型号： | AD7280AWBSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 20/48页 |
| 文件大小： | 0K |
| 描述： | IC BATT MON LI-ION AUTO 48LQFP |
| 标准包装： | 1 |
| 功能： | 电池监控器，过压/欠压保护 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 8 V ~ 30 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页当前第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD7280A
Note that 90 μs should be allowed before initiating any conver-
sions following any change to Bits[D15:D14]. This time should
be allowed between writing to the control register to change the
selected conversions and initiating the first conversion.
Conversions that are initiated by the rising edge of the CS pin
require two separate write commands to the control register. The
first command configures the AD7280A for the required
acquisition time; the second command, following a delay of
90 μs, initiates the conversion on the rising edge of CS.
After the completion of all requested conversions, the results
can be read back from either a single device or from all devices
in a daisy chain by using the SPI and daisy-chain interfaces. For
more information, see the Serial Interface section and the
Daisy-Chain Interface section.
As shown in Figure 32, a wait time, t WAIT , is required between the
completion of conversions and the start of readback. This time
is required to synchronize the high speed conversion clock and
the lower speed clock used for all other AD7280A operations.
The minimum value of t WAIT is 5 μs.
Acquisition Time
The time required to acquire an input signal depends on how
quickly the sampling capacitor is charged. This, in turn, depends
on the input impedance and any external components placed on
the analog inputs. The default acquisition time of the AD7280A
on initial power-up is 400 ns. This time can be increased in steps
of 400 ns up to 1.6 μs to provide flexibility in selecting external
components on the analog inputs. The acquisition time is selected
by writing to Bits[D6:D5] in the control register (see Table 9).
Table 9. Analog Input Acquisition Time
Conversion Averaging
The AD7280A includes an option where the acquisition and
conversion of each cell input can be repeated with an averaged
conversion result being stored in the individual register. The
averaged conversion result can then be read back through the
SPI interface in the same manner as a standard conversion result.
The AD7280A can be programmed, through Bits[D10:D9] of the
control register, to complete one, two, four, or eight conversions.
The default on power-up is a single conversion per channel, that
is, no averaging.
Selection of the two, four, or eight average options through the
control register causes the control sequence of both the high
voltage and low voltage input multiplexers to be reconfigured to
allow the additional acquisitions and conversions to be completed.
In each case, the requested number of conversions is completed
on each channel before beginning the acquisition and conversion
of the next channel in sequence. For example, if an average of two
conversions is requested, the new sequence is Voltage Channel 6,
Voltage Channel 6, Voltage Channel 5, Voltage Channel 5, Voltage
Channel 4, and so on.
It should also be noted that when the high voltage multiplexer
is reconfigured, 90 μs should be allowed before initiating any
conversions. This time should be allowed between writing to
the control register to select averaging and initiating the first
conversion. Conversions that are being initiated by the rising
edge of the CS pin require two separate write commands to the
control register. The first command configures the AD7280A
for the required averaging, and the second command, after a
delay of 90 μs, initiates the conversion on the rising edge of CS.
Suggested External Component Configuration on
Bits[D6:D5]
00
01
10
11
Acquisition Time
400 ns
800 ns
1.2 μs
1.6 μs
Analog Inputs
As described in the Acquisition Time section, the acquisition
time of the AD7280A is selected by the status of Bits[D6:D5] in
the control register. This provides flexibility in selecting external
components on the analog inputs. A suggested configuration
The acquisition time required is calculated using the following
formula:
t ACQ = 10 × (( R SOURCE + R ) × C )
for placing external components on the analog inputs to the
where:
R SOURCE should include any extra source impedance on the
analog input between the external capacitors (100 nF) and the
input pins. It does not include any extra source impedance, for
example, the 10 kΩ series resistors, which are between the
battery cells and the external capacitors.
R is the resistance seen by the track-and-hold amplifier looking
at the input, 300 Ω.
C is the sampling capacitance, that is, the value of the sampling
10k ?
10k ?
10k ?
10k ?
10k ?
10k ?
10k ?
100nF
100nF
100nF
100nF
100nF
100nF
VIN6
VIN5
VIN4
VIN3
VIN2
VIN1
VIN0
AD7280A
capacitor, 15 pF.
Figure 33. External Series Resistance and Shunt Capacitance
Rev. 0 | Page 20 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| AD780CR | IC VREF SERIES SHUNT PREC 8-SOIC |
| AD8280WASTZ-RL | IC LI-ION BATT MON 48LQFP |
| AD8383ACPZ | IC DECIMATING LCD DRIVER 48LFCSP |
| AD8384ASVZ | IC DRIVER LCD 6CH 10BIT 80-TQFP |
| AD8511ARUZ-REEL | IC MUX LCD DVR 11CH 3.3V 48TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7280AWBSTZ-RL | 功能描述:IC BATT MON LI-ION AUTO 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| AD7280BSTZ | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-RL | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-U6 | 制造商:Analog Devices 功能描述: |
| AD7280S-OB | 制造商:Sony Nec Optiarc America 功能描述:24X DVDRW SATA (BLACK) - Bulk |
发布紧急采购，3分钟左右您将得到回复。