参数资料
| 型号： | AD7280AWBSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 9/48页 |
| 文件大小： | 0K |
| 描述： | IC BATT MON LI-ION AUTO 48LQFP |
| 标准包装： | 1 |
| 功能： | 电池监控器，过压/欠压保护 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 8 V ~ 30 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页当前第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD7280A
Pin No.
21
22
23
24
25
26
27
28
29
30
31
32
33 to 38
39
40
41
42
Mnemonic
CS
SCLK
SDI
CNVST
SDOlo
SDO
ALERT
ALERTlo
V DRIVE
AV CC
AGND
AUX TERM
AUX6 to AUX1
C REF
V REF
REFGND
ALERThi
Description
Chip Select Input. The CS input is used to frame the input and output data on the SPI and daisy-chain
interfaces. On the master AD7280A device, the CS input is supplied from the DSP/microprocessor. When
the AD7280A acts as a slave in a daisy chain, this input should be connected to the CShi output of the
AD7280A immediately below it in potential in the daisy chain.
Serial Clock Input. On the master AD7280A device, the SCLK input is supplied from the DSP/microprocessor.
When the AD7280A acts as a slave in a daisy chain, this input should be connected to the SCLKhi output of
the AD7280A immediately below it in potential in the daisy chain.
Serial Data Input. Data to be written to the on-chip registers is provided on this input and is clocked into the
AD7280A on the falling edge of the SCLK input. On the master AD7280A device, SDI is the data input of the
SPI interface. When the AD7280A acts as a slave in a daisy chain, this input accepts data from the SDOhi
output of the AD7280A immediately below it in potential in the daisy chain.
Convert Start Input. The conversion is initiated on the falling edge of CNVST. On the master AD7280A, the
CNVST pulse is supplied from the DSP/microprocessor; this input can also be tied to DV CC and the conversion
initiated through the seria l interface. When the AD7280A acts as a slave in a daisy chain, this input should be
connected to the CNVSThi output of the AD7280A immediately below it in potential in the daisy chain.
Serial Data Output in Daisy-Chain Mode. On the master AD7280A device, this output should be connected
to V SS either directly or through a pull-down, 1 kΩ resistor. When the AD7280A acts as a slave in a daisy chain,
this output should be connected to the SDIhi input of the AD7280A immediately below it in potential in the
daisy chain.
Serial Data Output. The conversion output data or the register output data is supplied to this pin as a serial
data stream. The bits are clocked out on the rising edge of the SCLK input; 32 SCLKs are required to access
the data. On the master AD7280A device, the SDO output should be connected to the DSP/microprocessor.
The SDO outputs of the remaining AD7280As in the daisy chain should be connected to V SS either directly or
through a pull-down, 1 kΩ resistor.
Digital Output. This flag indicates cell or auxiliary ADC input overvoltage or undervoltage. The ALERT output of
the master AD7280A should be connected to the DSP/microprocessor. The ALERT outputs of the remaining
AD7280As in the daisy chain should be connected to V SS either directly or through a pull-down, 1 kΩ resistor.
Alert Output in Daisy-Chain Mode. On the master AD7280A, this output should be connected to V SS either
directly or through a pull-down, 1 kΩ resistor. When the AD7280A acts as a slave in a daisy chain, this output
should be connected to the ALERThi input of the AD7280A immediately below it in potential in the daisy chain.
Logic Power Supply Input. The voltage supplied at this pin determines the voltage at which the SPI interface
operates. This pin should be decoupled to DGND. On the master AD7280A device, the voltage range on this
pin is 2.7 V to 5.5 V. The V DRIVE voltage can be different from the voltage at AV CC and DV CC , but it should never
exceed either by more than 0.3 V. The V DRIVE pin of the remaining AD7280As in the daisy chain should be
connected to V REG .
Analog Supply Voltage for the ADC Core, 4.9 V to 5.5 V. The AV CC and DV CC voltages should ideally be at the
same potential. For best performance, it is recommended that the AV CC and DV CC pins be shorted together to
ensure that the voltage difference between them never exceeds 0.3 V, even on a transient basis. This supply
should be decoupled to AGND. Place 100 nF decoupling capacitors on the AV CC pin. The AV CC supply pin
should be connected to the V REG output.
Analog Ground. This pin is the ground reference point for all analog circuitry on the AD7280A. This input should
be at the same potential as the base of the series-connected battery cells. The AGND and DGND voltages
should ideally be at the same potential and must not be more than 0.3 V apart, even on a transient basis.
Thermistor Termination Resistor Input. If this function is not required in the application, it is recommended
that this pin be connected to V REG through a 10 kΩ resistor.
Auxiliary, Single-Ended 5 V ADC Inputs. If any of these inputs is not required in the application, it is
recommended that the pin be connected to V REG through a 10 kΩ resistor.
Reference Capacitor. A 100 nF decoupling capacitor to REFGND should be placed on this pin.
Reference Output, 2.5 V. The on-chip reference is available on this pin for use external to the AD7280A.
A 1 μF decoupling capacitor to REFGND is recommended on this pin.
Reference Ground. This pin is the ground reference point for the internal band gap reference circuitry on
the AD7280A. The REFGND voltage should be at the same potential as the AGND voltage.
Alert Input in Daisy-Chain Mode. The alert signal from each AD7280A in the daisy chain is passed through
the ALERTlo output and the ALERThi input of each AD7280A in the chain and is supplied to the DSP/micro-
processor through the ALERT output of the master AD7280A. This input should be connected to the ALERTlo
output of the AD7280A immediately above it in potential in the daisy chain. The AD7280A at the highest
potential in the stack does not require an alert input; in this case, the pin should be connected to V DD
through a 1 kΩ resistor.
Rev. 0 | Page 9 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| AD780CR | IC VREF SERIES SHUNT PREC 8-SOIC |
| AD8280WASTZ-RL | IC LI-ION BATT MON 48LQFP |
| AD8383ACPZ | IC DECIMATING LCD DRIVER 48LFCSP |
| AD8384ASVZ | IC DRIVER LCD 6CH 10BIT 80-TQFP |
| AD8511ARUZ-REEL | IC MUX LCD DVR 11CH 3.3V 48TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7280AWBSTZ-RL | 功能描述:IC BATT MON LI-ION AUTO 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| AD7280BSTZ | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-RL | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-U6 | 制造商:Analog Devices 功能描述: |
| AD7280S-OB | 制造商:Sony Nec Optiarc America 功能描述:24X DVDRW SATA (BLACK) - Bulk |
发布紧急采购，3分钟左右您将得到回复。