参数资料
| 型号： | AD7280AWBSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/48页 |
| 文件大小： | 0K |
| 描述： | IC BATT MON LI-ION AUTO 48LQFP |
| 标准包装： | 1 |
| 功能： | 电池监控器，过压/欠压保护 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 8 V ~ 30 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD7280A
SERIAL INTERFACE
The AD7280A serial interface is Mode 1 SPI compliant, that is,
the clock polarity (CPOL) is 0, and the clock phase (CPHA) is 1.
The interface consists of four signals: CS, SCLK, SDI, and SDO.
The SDI line is used to transfer data into the on-chip registers,
and the SDO line is used to read the on-chip registers and
conversion result registers. SCLK is the serial clock input for the
device; all data transfers, either on SDI or on SDO, take place
with respect to SCLK. Data is clocked into the AD7280A on the
SCLK falling edge. Data is clocked out of the AD7280A on the
SCLK rising edge. The CS input is used to frame the serial data
being transferred to or from the device.
The AD7280A allows 32-bit d at a transfer only and resets a
counter on the rising edge of CS to ensure that the AD7280A is
automatically resynchronized with the DSP/microprocessor on
every falling edge of CS. Individual 8-bit or 16-bit words can be
used to assemble a 32-bit command, but a single 32-bit wide CS
frame is required to correctly structure the assembly of the
32-bit command.
The rising edge of CS can also be used to initiate the sequence of
conversions by writing to the upper byte of the control register.
AD7280A. See the Daisy-Chain Interface section for more
information about the daisy-chain interface.
WRITING TO THE AD7280A
In a battery monitoring application, up to eight AD7280As can
be daisy-chained to allow up to 48 individual Li-Ion cell voltages
to be monitored. Each write operation must, therefore, include
a device address and a register address, in addition to the data
to be written. An additional identifier bit is also required when
addressing all AD7280As in the daisy chain. The AD7280A SPI
interface, in combination with the daisy-chain interface, allows
any register in the stack of eight AD7280As to be updated using
one 32-bit write cycle. The 32-bit write sequence is shown in
included in each write command.
Device Address
The device address is a 5-bit address that allows each individual
AD7280A in the battery monitoring stack to be uniquely
identified. On initial power-up, each AD7280A is configured
with a default address of 0x00. A simple sequence of commands
allows each AD7280A to recognize its unique device address in
the stack (see the Initializing the AD7280A section).
Table 20. 32-Bit Write Cycle
This device address can then be locked to the AD7280A and used
in subsequent read and write commands. The device address is
written to and read from the AD7280A stack in reverse order,
that is, LSB first.
Register Address
The register map for the AD7280A is provided in Table 13. Each
register address is six bits long and is used when writing to or
reading from the on-chip registers of the AD7280A.
Register Data
When issuing a write command to a part in the stack of
AD7280A devices, the data to be written is an 8-bit word. As
shown in Table 13, all read/write registers are eight bits wide.
For more information about the correct settings for each
register, see the Register Map section.
Address All Parts
The AD7280A allows write commands to be issued simultane-
ously to all devices in the daisy chain, as well as write commands to
individual AD7280As. A write to all devices in the daisy chain is
completed by setting Bit D12 of the write command to 1. When
issuing a write all command, the device address should be set to
0x00. This device address is also used to calculate the 8-bit CRC
for transmission with the write all command.
8-Bit CRC
The AD7280A includes an 8-bit cyclic redundancy check (CRC)
on all write commands to either individual devices or to a chain
of devices. An AD7280A that receives an invalid CRC in the
write command does not execute the command. The CRC on
the write command is calculated based on Bits[D31:D11] of the
write command. These bits include the device address, the
register address, the data to be written, the address all parts bit,
and Bit D11. For more information about the CRC, see the
Bit Pattern (010)
A required fixed bit pattern of 010 to Bits[D2:D0] of the 32-bit
write command of the AD7280A provides an additional stage of
verification. The correct position of this bit pattern is verified
on each write command received by the AD7280A. An
AD7280A that receives an incorrect bit pattern in the write
command does not execute the command.
Device Address 1
D31 to D27
Register Address
D26 to D21
Register Data
D20 to D13
Address All Parts
D12
Reserved (0 Bit)
D11
8-Bit CRC
D10 to D3
Bit Pattern (010)
D2 to D0
1
The device address is configured LSB first. For example, to address the second device in the stack, that is, the first slave device, the sequence of bits input to the
AD7280A should be 10000. The register address, data bits, and CRC bits are input MSB first.
Rev. 0 | Page 32 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| AD780CR | IC VREF SERIES SHUNT PREC 8-SOIC |
| AD8280WASTZ-RL | IC LI-ION BATT MON 48LQFP |
| AD8383ACPZ | IC DECIMATING LCD DRIVER 48LFCSP |
| AD8384ASVZ | IC DRIVER LCD 6CH 10BIT 80-TQFP |
| AD8511ARUZ-REEL | IC MUX LCD DVR 11CH 3.3V 48TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7280AWBSTZ-RL | 功能描述:IC BATT MON LI-ION AUTO 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| AD7280BSTZ | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-RL | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-U6 | 制造商:Analog Devices 功能描述: |
| AD7280S-OB | 制造商:Sony Nec Optiarc America 功能描述:24X DVDRW SATA (BLACK) - Bulk |
发布紧急采购，3分钟左右您将得到回复。