参数资料
| 型号： | AD7280AWBSTZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 30/48页 |
| 文件大小： | 0K |
| 描述： | IC BATT MON LI-ION AUTO 48LQFP |
| 标准包装： | 1 |
| 功能： | 电池监控器，过压/欠压保护 |
| 电池化学： | 锂离子（Li-Ion） |
| 电源电压： | 8 V ~ 30 V |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-LQFP |
| 供应商设备封装： | 48-LQFP（7x7） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页当前第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
AD7280A
CELL UNDERVOLTAGE REGISTER
The cell undervoltage register determines the low voltage thresh-
old of the AD7280A. Cell voltage conversions lower than the
undervoltage threshold trigger the alert output. The AD7280A
allows the user to set the undervoltage threshold to a value from
1 V to 5 V. The resolution of the undervoltage threshold is eight
bits, that is, 16 mV. The default value of the undervoltage threshold
on power-up is 0x00 (1 V).
AUX ADC OVERVOLTAGE REGISTER
The AUX ADC overvoltage register determines the high voltage
threshold of the AD7280A auxiliary ADC inputs. Conversions
CELL BALANCE REGISTER
The cell balance register determines the status of the six cell
balance outputs. The six CBx outputs are set by writing to
Bits[D7:D2] of the cell balance register. The cell balance register
is reset by a software reset or following a hardware power-down.
The default value of the cell balance register on power-up is 0x00.
Table 15. Cell Balance Register Settings
Bits Description
D7 Set CB6 output
0 = output off
1 = output on
that exceed this threshold trigger the alert output. The AD7280A
allows the user to set the threshold to a value from 0 V to 5 V. The
resolution is eight bits, that is, 19 mV. The default value of the
auxiliary ADC overvoltage threshold on power-up is 0xFF (5 V).
AUX ADC UNDERVOLTAGE REGISTER
The AUX ADC undervoltage register determines the low voltage
threshold of the AD7280A auxiliary ADC inputs. Conversions
that are lower than this threshold trigger the alert output. The
AD7280A allows the user to set the threshold to a value from 0 V
to 5 V. The resolution is eight bits, that is, 19 mV. The default
value of the AUX ADC undervoltage threshold on power-up
is 0x00 (0 V).
ALERT REGISTER
The alert register determines the configuration of the alert
function. The alert can be configured as a static or dynamic
D6
D5
D4
D3
D2
[D1:D0]
Set CB5 output
0 = output off
1 = output on
Set CB4 output
0 = output off
1 = output on
Set CB3 output
0 = output off
1 = output on
Set CB2 output
0 = output off
1 = output on
Set CB1 output
0 = output off
1 = output on
Reserved; set to 0
signal.
CBx TIMER REGISTERS
?
?
The static signal is a high signal that is pulled low to
indicate that an overvoltage or undervoltage on a cell
or on the auxiliary ADC has occurred.
The dynamic signal is a square wave, the frequency
The CBx timer registers allow the user to program individual times
for each cell balance output. The AD7280A allows the user to set
the CBx timer to a value from 0 minutes to 36.9 minutes. The
resolution of the CBx timers is 71.5 sec. The default value of the
of which can be set to 100 Hz, 1 kHz, or 10 kHz.
When a number of AD7280As are operating in daisy-chain
mode, the selection of static or dynamic alert is set on the
AD7280A at the highest potential in the chain only. The alert
registers on the remaining AD7280As in the chain should be
programmed to pass the alert signal through the chain. Each
part passes the static or dynamic alert signal through the chain
or pulls the signal low to indicate that an overvoltage or under-
voltage on a cell or on the auxiliary ADC has occurred.
CBx timer registers on power-up is 0x00. When the CBx timer
value is set to 0x00, the CBx timer is not activated; that is, the CBx
outputs are all controlled by the contents of the cell balance
Outputs section.
Table 16. CBx Timer Register Settings
Bits Description
[D7:D3] 5-bit binary code to set the CB timer to a value
from 0 minutes to 36.9 minutes
See Table 11 and Table 12 for more information about the alert
[D2:D0]
Reserved; set to 000
register settings. The default value of the alert register on
power-up is 0x00.
Rev. 0 | Page 30 of 48
相关PDF资料 |
PDF描述 |
|---|---|
| AD780CR | IC VREF SERIES SHUNT PREC 8-SOIC |
| AD8280WASTZ-RL | IC LI-ION BATT MON 48LQFP |
| AD8383ACPZ | IC DECIMATING LCD DRIVER 48LFCSP |
| AD8384ASVZ | IC DRIVER LCD 6CH 10BIT 80-TQFP |
| AD8511ARUZ-REEL | IC MUX LCD DVR 11CH 3.3V 48TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7280AWBSTZ-RL | 功能描述:IC BATT MON LI-ION AUTO 48LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电池管理 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 功能:电池监控器 电池化学:碱性，锂离子，镍镉，镍金属氢化物 电源电压:1 V ~ 5.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SOT-23-6 供应商设备封装:SOT-6 包装:带卷 (TR) |
| AD7280BSTZ | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-RL | 制造商:Analog Devices 功能描述: |
| AD7280BSTZ-U6 | 制造商:Analog Devices 功能描述: |
| AD7280S-OB | 制造商:Sony Nec Optiarc America 功能描述:24X DVDRW SATA (BLACK) - Bulk |
发布紧急采购，3分钟左右您将得到回复。