- 您现在的位置：买卖IC网 > PDF目录373897 > AD73311LAR (ANALOG DEVICES INC) Low Cost, Low Power CMOS General Purpose Analog Front End PDF资料下载
参数资料
| 型号： | AD73311LAR |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 通信及网络 |
| 英文描述： | Low Cost, Low Power CMOS General Purpose Analog Front End |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO20 |
| 封装： | 0.300 INCH, SOIC-20 |
| 文件页数： | 16/36页 |
| 文件大小： | 382K |
| 代理商： | AD73311LAR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
REV. A
AD73311L
–16–
Operating Modes
There are
fi
ve operating modes available on the AD73311L.
Two of these
—
Digital Loop-Back and Sport Loop-Back
—
are
provided as diagnostic modes with the other three, Program,
Data and Mixed Program/Data, being available for general
purpose use. The device con
fi
guration
—
register settings
—
can
be changed only in Program and Mixed Program/Data Modes.
In all modes, transfers of information to or from the device
occur in 16-bit packets, therefore the DSP engine
’
s SPORT will
be programmed for 16-bit transfers.
Program (Control) Mode
In Program Mode, CRA:0 = 0, the user writes to the control
registers to set up the device for desired operation
—
SPORT
operation, cascade length, power management, input/output
gain, etc. In this mode, the 16-bit information packet sent to the
device by the DSP engine is interpreted as a control word whose
format is shown in Table X. In this mode, the user must address
the device to be programmed using the address
fi
eld of the control
word. This
fi
eld is read by the device and if it is zero (000 bin)
then the device recognizes the word as being addressed to it. If the
address
fi
eld is not zero, it is then decremented and the control
word is passed out of the device
—
either to the next device in a
cascade or back to the DSP engine. This 3-bit address format
allows the user to uniquely address any one of up to eight devices
in a cascade; please note that this addressing scheme is valid only
in sending control information to the device
—
a different format
is used to send DAC data to the device(s). In a single codec
con
fi
guration, all control word addresses must be zero, other-
wise they will not be recognized; in a multi-codec con
fi
guration
all addresses from zero to N-1 (where
N
= number of devices in
cascade) are valid.
Following reset, when the SE pin is enabled, the codec responds
by raising the SDOFS pin to indicate that an output sample
event has occurred. Control words can be written to the device to
coincide with the data being sent out of the SPORT, as shown in
Figure 10, or they can lag the output words by a time interval
that should not exceed the sample interval. After reset, output
frame sync pulses will occur at a slower default sample rate, which
is DMCLK/2048, until Control Register B is programmed after
which the SDOFS pulses will occur at a rate set by the DIR0-1 bits
of CRB. This is to allow slow controller devices to establish
communication with the AD73311L. During Program Mode,
the data output by the device is random and should not be inter-
preted as ADC data.
Data Mode
Once the device has been con
fi
gured by programming the cor-
rect settings to the various control registers, the device may exit
Program Mode and enter Data Mode. This is done by program-
ming the DATA/
PGM
(CRA:0) bit to a 1 and MM (CRA:1) to
0. Once the device is in Data Mode, the 16-bit input data frame
is now interpreted as DAC data rather than a control frame. This
data is therefore loaded directly to the DAC register. In Data
Mode, as the entire input data frame contains DAC data, the
device relies on counting the number of input frame syncs
received at the SDIFS pin. When that number equals the device
count stored in the device count
fi
eld of CRA, the device knows
that the present data frame being received is its own DAC update
data. When the device is in normal Data Mode (i.e., mixed
mode disabled), it must receive a hardware reset to reprogram
any of the control register settings. In a single codec con
fi
gura-
tion, each 16-bit data frame sent from the DSP to the device is
interpreted as DAC data. The default device count is 1, therefore
each input frame sync will cause the 16-bit data frame to be
loaded to the DAC register.
Mixed Program/Data Mode
This mode allows the user to send control words to the device
along with the DAC data. This permits adaptive control of the
device whereby control of the input/output gains can be effected
by interleaving control words along with the normal flow of
DAC data. The standard data frame remains 16 bits, but now
the MSB is used as a flag bit to indicate whether the remaining
15 bits of the frame represent DAC data or control information.
In the case of DAC data, the 15 bits are loaded with MSB justi-
fi
cation and LSB set to 0 to the DAC register. Mixed mode is
enabled by setting the MM bit (CRA:1) to 1 and the DATA/
PGM
bit (CRA:0) to 1. In the case where control setting changes will
be required during normal operation, this mode allows the
ability to load both control and data information with the slight
inconvenience of formatting the data. Note that the output
samples from the ADC will also have the MSB set to zero to
indicate it is a data word.
Digital Loop-Back
This mode can be used for diagnostic purposes and allows the
user to feed the ADC samples from the ADC register directly to
the DAC register. This forms a loop-back of the analog input to
the analog output by reconstructing the encoded signal using
the decoder channel. The serial interface will continue to work,
which allows the user to control gain settings, etc. Only when
DLB is enabled with Mixed Mode operation can the user disable
the DLB, otherwise the device must be reset.
Sport Loop-Back
This mode allows the user to verify the DSP interfacing and
connection by writing words to the SPORT of the device and
have them returned back unchanged at the next sample interval.
The frame sync and data word that are sent to the device are
returned via the output port. Again, SLB mode can only be
disabled when used in conjunction with mixed mode, otherwise
the device must be reset.
Analog Loop-Back
In Analog Loop-Back mode, the differential DAC output is
connected, via a loop-back switch, to the ADC input (see Figure
12). This mode allows the ADC channel to check functionality
of the DAC channel as the reconstructed output signal can be
monitored using the ADC as a sampler. Analog Loop-Back is
enabled by setting the ALB bit (CRF:7).
相关PDF资料 |
PDF描述 |
|---|---|
| AD73311L | Low Cost, Low Power CMOS General Purpose Analog Front End Processor(低成本，低功耗的CMOS通用双模拟前端处理器) |
| AD73311 | Low Cost, Low Power CMOS General Purpose Analog Front End Processor(低成本、低功耗、CMOS通用模拟前端处理器) |
| AD73322LARU | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
| AD73322AR | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
| AD73322AST | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD73311LAR-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Tape and Reel |
| AD73311LAR-REEL7 | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Tape and Reel |
| AD73311LARS | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Bulk 制造商:Analog Devices 功能描述:IC AUDIO CODEC |
| AD73311LARS-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP T/R |
| AD73311LARSREEL7 | 制造商:AD 功能描述:New |
发布紧急采购，3分钟左右您将得到回复。