- 您现在的位置：买卖IC网 > PDF目录373897 > AD73311LAR (ANALOG DEVICES INC) Low Cost, Low Power CMOS General Purpose Analog Front End PDF资料下载
参数资料
| 型号： | AD73311LAR |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 通信及网络 |
| 英文描述： | Low Cost, Low Power CMOS General Purpose Analog Front End |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO20 |
| 封装： | 0.300 INCH, SOIC-20 |
| 文件页数： | 32/36页 |
| 文件大小： | 382K |
| 代理商： | AD73311LAR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页
REV. A
AD73311L
–32–
Con
fi
guring a Cascade of Two AD73311Ls to Operate in
Data Mode
1
This section describes the typical sequence of control words that
are required to be sent to a cascade of two AD73311Ls to set
them up for data mode operation. In this sequence Registers B,
C and A are programmed before the device enters data mode.
This description panel refers to Table XXI.
At each sampling event, a pair of SDOFS pulses will be observed
which will cause a pair of control (programming) words to be
sent to the device from the DSP. It is advisable that each pair of
control words should program a single register in each device.
The sequence to be followed is Device 2 followed by Device 1.
In Step 1, we have the
fi
rst output sample event following device
reset. The SDOFS signal is raised on both devices simultaneously,
which prepares the DSP Rx register to accept the ADC word
from Device 2, while SDOFS from Device 1 becomes an SDIFS
to Device 2. As the SDOFS of Device 2 is coupled to the DSP
’
s
TFS and RFS, and to the SDIFS of Device 1, this event also
forces a new control word to be output from the DSP Tx regis-
ter to Device 1.
In Step 2, we observe the status of the devices following the
transmission of the
fi
rst control word. The DSP has received the
output word from Device 2, while Device 2 has received the
output word from Device 1. Device 1 has received the Control
word destined for Device 2. At this stage, the SDOFS of both
devices are again raised because Device 2 has received Device
1
’
s output word, and as it is not a valid control word addressed
to Device 2, it is passed on to the DSP. Likewise, Device 1 has
received a control word destined for Device 2-address
fi
eld is
not zero-and it decrements the address
fi
eld of the control word
and passes it on.
Step 3 shows completion of the
fi
rst series of control word
writes. The DSP has now received both output words and each
device has received a control word that addresses control register
B and sets the internal MCLK divider ratio to 1, SCLK rate to
DMCLK/2 and sampling rate to DMCLK/256. Note that both
devices are updated simultaneously as both receive the addressed
control word at the same time. This is an important factor in
cascaded operation as any latency between updating the SCLK
or DMCLK of devices can result in corrupted operation. This
will not happen in the case of an FSLB con
fi
guration as shown
here, but must be taken into account in a nonFSLB con
fi
gura-
tion. One other important observation of this sequence is that
the data words are received and transmitted in reverse order,
i.e., the ADC words are received by the DSP, Device 2
fi
rst,
then Device 1 and, similarly, the transmit words from the DSP
are sent to Device 2
fi
rst, then to Channel 1. This ensures that
all devices are updated at the same time. Steps 4
–
6 are similar to
APPENDIX C
Steps 1
–
3 but, instead, program Control Register C to power-up
the analog sections of the device (ADCs, DACs and reference).
Steps 7
–
9 are similar to Steps 1
–
3 but, instead, program Con-
trol Register A, with a device count
fi
eld equal to two devices in
cascade and sets the
PGM
/DATA bit to one to put the device
in data mode.
In Step 10, the programming phase is complete and we now
begin actual device data read and write. The words loaded into
the serial registers of the two devices at the ADC sampling
event now contain valid ADC data and the words written to the
devices from the DSP
’
s Tx register will now be interpreted as
DAC words. The DSP Tx register contains the DAC word for
Device 2.
In Step 11, the
fi
rst DAC word has been transmitted into the
cascade and the ADC word from Device 2 has been read from
the cascade. The DSP Tx register now contains the DAC
word for Device 1. As the words being sent to the cascade are
now being interpreted as 16-bit DAC words, the addressing
scheme now changes from one where the address was embed-
ded in the transmitted word, to one where the serial port now
counts the SDIFS pulses. When the number of SDIFS pulses
received equals the value in the Device count
fi
eld of Control
Register A, the length of the cascade-each device updates its
DAC register with the present word in its serial register. In
Step 11 each device has received only one SDIFS pulse; Device
2 received one SDIFS from the SDOFS of Device 1 when it
sent its ADC word, and Device 1 received one SDIFS pulse
when it received the DAC word for Device 2 from the DSP
’
s
Tx register. Therefore, each device raises its SDOFS line to
pass on the current word in its serial register, and each device
now receives another SDIFS pulse.
Step 12 shows the completion of an ADC read and DAC write
cycle. Following Step 11, each device has received two SDIFS
pulses that equal the setting of the device count
fi
eld in Control
Register A. The DAC register in each device is now updated
with the contents of the word that accompanied the SDIFS
pulse that satis
fi
ed the device count requirement. The internal
frame sync counter is now reset to zero and will begin counting
for the next DAC update cycle. Steps 10
–
12 are repeated on
each sampling event.
NOTE
1
This sequence assumes that the DSP SPORT
’
s Rx and Tx interrupts are
enabled. It is important to ensure that there is no latency (separation) between
control words in a cascade con
fi
guration. This is especially the case when
programming Control Registers A and B, as they must be updated synchro-
nously in each channel.
相关PDF资料 |
PDF描述 |
|---|---|
| AD73311L | Low Cost, Low Power CMOS General Purpose Analog Front End Processor(低成本，低功耗的CMOS通用双模拟前端处理器) |
| AD73311 | Low Cost, Low Power CMOS General Purpose Analog Front End Processor(低成本、低功耗、CMOS通用模拟前端处理器) |
| AD73322LARU | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
| AD73322AR | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
| AD73322AST | Low Cost, Low Power CMOS General-Purpose Dual Analog Front End |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD73311LAR-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Tape and Reel |
| AD73311LAR-REEL7 | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SOIC W T/R 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Tape and Reel |
| AD73311LARS | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP 制造商:Rochester Electronics LLC 功能描述:SINGLE-CHANNEL AFE I.C. - Bulk 制造商:Analog Devices 功能描述:IC AUDIO CODEC |
| AD73311LARS-REEL | 制造商:Analog Devices 功能描述:Audio Codec 1ADC / 1DAC 16-Bit 20-Pin SSOP T/R |
| AD73311LARSREEL7 | 制造商:AD 功能描述:New |
发布紧急采购，3分钟左右您将得到回复。