- 您现在的位置：买卖IC网 > PDF目录10346 > AD7441BRTZ-REEL7 (Analog Devices Inc)IC ADC 10BIT W/DIFF INP SOT-23-8 PDF资料下载
参数资料
| 型号： | AD7441BRTZ-REEL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/25页 |
| 文件大小： | 0K |
| 描述： | IC ADC 10BIT W/DIFF INP SOT-23-8 |
| 标准包装： | 1 |
| 位数： | 10 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 9.25mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | SOT-23-8 |
| 供应商设备封装： | SOT-23-8 |
| 包装： | 标准包装 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 其它名称： | AD7441BRTZ-REEL7DKR |
AD7441/AD7451
Rev. D | Page 20 of 24
POWER VS. THROUGHPUT RATE
By using the power-down mode on the device when not con-
verting, the average power consumption of the ADC decreases
at lower throughput rates. Figure 32 shows how, as the through-
put rate is reduced, the device remains in its power-down state
longer and the average power consumption reduces accordingly.
For example, if the AD7441/AD7451 are operated in continuous
sampling mode with a throughput rate of 100 kSPS and an SCLK
of 18 MHz, and the device is placed in the power-down mode
between conversions, then the power consumption during
normal operation equals 9.25 mW maximum (for VDD = 5 V).
If the power-up time is one dummy cycle (1 μs) and the remain-
ing conversion time is another cycle (1 μs), then the AD7441/
AD7451 can be said to dissipate 9.25 mW for 2 μs during each
conversion cycle. (This power consumption figure assumes a
very short time to enter power-down mode. This power figure
increases as the burst of clocks used to enter power-down mode
is increased). The AD7441/AD7451 consume just 5 μW for the
remaining 8 μs.
Calculate the power numbers in Figure 32 as follows:
If the throughput rate = 100 kSPS, then the cycle time = 10 μs,
and the average power dissipated during each cycle is
(2/10) × 9.25 mW = 1.85 mW
For the same scenario, if VDD = 3 V, the power dissipation
during normal operation is 4 mW maximum.
The AD7441/AD7451 can now be said to dissipate 4 mW for
2 μs during each conversion cycle.
The average power dissipated during each cycle with a
throughput rate of 100 kSPS is, therefore,
(2/10) × 4 mW = 0.8 mW
THROUGHPUT (kSPS)
100
0350
P
O
WE
R
(
m
W)
0.01
50
100
150
200
250
300
0.1
1
10
VDD = 5V
VDD = 3V
03
15
3-
0
32
Figure 32. Power vs. Throughput Rate for Power-Down Mode
For optimum power performance in throughput rates above
320 kSPS, it is recommended that the serial clock frequency be
reduced.
MICROPROCESSOR AND DSP INTERFACING
The serial interface on the AD7441/AD7451 allows the part to
be connected directly to a range of different microprocessors.
This section explains how to interface the AD7441/AD7451
with some of the more common microcontroller and DSP serial
interface protocols.
AD7441/AD7451 to ADSP-21xx
The ADSP-21xx family of DSPs is interfaced directly to the
AD7441/AD7451 without any glue logic required. The SPORT
control register is set up as follows:
TFSW = RFSW = 1
Alternate framing
INVRFS = INVTFS = 1
Active low frame signal
DTYPE = 00
Right justify data
SLEN = 1111
16-bit data-words
ISCLK = 1
Internal serial clock
TFSR = RFSR = 1
Frame every word
IRFS = 0
ITFS = 1
To implement power-down mode, SLEN is set to 1001 to issue
an 8-bit SCLK burst.
The connection diagram is shown in Figure 33. ADSP-21xx has
the TFS and RFS of the SPORT tied together, with TFS set as an
output and RFS set as an input. The DSP operates in alternate
framing mode, and the SPORT control register is set up as
described. The frame synchronization signal generated on the
TFS is tied to CS, and, as with all signal processing applications,
equidistant sampling is necessary. However, in this example,
the timer interrupt is used to control the sampling rate of the
ADC, and, under certain conditions, equidistant sampling
cannot be achieved.
AD7441/
AD7451*
ADSP-21xx*
SCLK
DR
RFS
TFS
SCLK
SDATA
CS
*ADDITIONAL PINS REMOVED FOR CLARITY.
0
31
53
-0
33
Figure 33. Interfacing to the ADSP-21xx
相关PDF资料 |
PDF描述 |
|---|---|
| MAX9725AETC+T | IC AMP AUDIO .025W STER 12TQFN |
| MS27656T13B8P | CONN RCPT 8POS WALL MNT W/PINS |
| MS27656E13B8P | CONN RCPT 8POS WALL MNT W/PINS |
| MAX9725BETC+T | IC AMP AUDIO .025W STER 12TQFN |
| VI-B1T-MW-S | CONVERTER MOD DC/DC 6.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD744AH | 制造商:Analog Devices 功能描述:OP Amp Single GP 制造商:Rochester Electronics LLC 功能描述:PRECISION BIPOLAR OP AMP - Bulk |
| AD744AQ | 功能描述:IC OPAMP BIFET 13MHZ PREC 8CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:150 系列:- 放大器类型:音频 电路数:2 输出类型:- 转换速率:5 V/µs 增益带宽积:12MHz -3db带宽:- 电流 - 输入偏压:100nA 电压 - 输入偏移:500µV 电流 - 电源:6mA 电流 - 输出 / 通道:50mA 电压 - 电源，单路/双路(±):4 V ~ 32 V，±2 V ~ 16 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:8-TSSOP 包装:管件 |
| AD744AQ/+ | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage-Feedback Operational Amplifier |
| AD744AR | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision, 500 ns Settling BiFET Op Amp |
| AD744BQ | 功能描述:IC OPAMP BIFET 13MHZ PREC 8CDIP RoHS:否 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:2,500 系列:Excalibur™ 放大器类型:J-FET 电路数:1 输出类型:- 转换速率:45 V/µs 增益带宽积:10MHz -3db带宽:- 电流 - 输入偏压:20pA 电压 - 输入偏移:490µV 电流 - 电源:1.7mA 电流 - 输出 / 通道:48mA 电压 - 电源，单路/双路(±):4.5 V ~ 38 V，±2.25 V ~ 19 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商设备封装:8-SOIC 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。