- 您现在的位置：买卖IC网 > PDF目录10530 > AD7664ACPZ (Analog Devices Inc)IC ADC 16BIT UNIPOLAR 48-LFCSP PDF资料下载
参数资料
| 型号： | AD7664ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT UNIPOLAR 48-LFCSP |
| 标准包装： | 13 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 570k |
| 数据接口： | 串行，并联 |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 115mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个伪差分，单极 |
| 配用： | EVAL-AD7664CBZ-ND - BOARD EVALUATION FOR AD7664 |
REV. E
–18–
AD7664
External Clock Data Read during Conversion
Figure 20 shows the detailed timing diagram of this method.
During a conversion, while both
CS and RD are LOW, the result
of the previous conversion can be read. The data is shifted out
MSB first with 16 clock pulses, and is valid on both the rising and
falling edge of the clock. The 16 bits have to be read before the
current conversion is complete; otherwise, RDERROR is pulsed
HIGH and can be used to interrupt the host interface to
prevent incomplete data reading. There is no daisy-chain
feature in this mode and RDC/SDIN input should always be tied
either HIGH or LOW.
To reduce performance degradation due to digital activity, a fast
discontinuous clock of at least 18 MHz when in Impulse Mode,
25 MHz when in Normal Mode, or 40 MHz when in Warp
Mode is recommended to ensure that all the bits are read during
the first half of the conversion phase. It is also possible to begin
to read the data after conversion and continue to read the last bits
even after a new conversion has been initiated. That allows the use of
a slower clock speed such as 14 MHz in Impulse Mode, 18 MHz
in Normal Mode, and 25 MHz in Warp Mode.
MICROPROCESSOR INTERFACING
The AD7664 is ideally suited for traditional dc measurement
applications supporting a microprocessor and ac signal processing
applications interfacing to a digital signal processor. The AD7664
is designed to interface either with a parallel 8-bit or 16-bit wide
interface, or with a general-purpose serial port or I/O ports on
a microcontroller. A variety of external buffers can be used
with the AD7664 to prevent digital noise from coupling into the
ADC. The following section discusses the use of an AD7664
with an ADSP-219x SPI equipped DSP.
SPI Interface (ADSP-219x)
Figure 21 shows an interface diagram between the AD7664 and
an SPI-equipped ADSP-219x. To accommodate the slower speed
of the DSP, the AD7664 acts as a slave device and data must be
read after conversion. This mode also allows the daisy-chain
feature. The convert command can be initiated in response to
an internal timer interrupt. The reading process can be initi-
ated in response to the end-of-conversion signal (BUSY going
LOW) using an interrupt line of the DSP. The serial interface
(SPI) on the ADSP-219x is configured for master mode—
(MSTR) = 1, Clock Polarity bit (CPOL) = 0, Clock Phase bit
(CPHA) = 1, and SPI Interrupt Enable (TIMOD) = 00— by
writing to the SPI control register (SPICLTx). To meet all
timing requirements, the SPI clock should be limited to 17
Mbps, which allows it to read an ADC result in less than 1
s.
When a higher sampling rate is desired, use of one of the
parallel interface modes is recommended.
SPIxSEL (PFx)
ADSP-219x*
CNVST
AD7664*
CS
BUSY
MISOx
SCKx
PFx or TFSx
SDOUT
SCLK
RD
INVSCLK
EXT/
INT
SER/
PAR
DVDD
*ADDITIONAL PINS OMITTED FOR CLARITY
PFx
Figure 21. Interfacing the AD7664 to an SPI Interface
SDOUT
CS
SCLK
D1
D0
X
D15
D14
D13
12
3
14
15
16
t3
t35
t36 t37
t31
t32
t16
CNVST
BUSY
EXT/
INT = 1
INVSCLK = 0
RD = 0
Figure 20. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
相关PDF资料 |
PDF描述 |
|---|---|
| MS3120E12-10P | CONN RECEPT 10POS W/PINS CRIMP |
| 97-3108B-18-12P | CONN PLUG RT ANG 6POS W/PINS |
| LTC2223CUK#PBF | IC ADC 12BIT 80MSPS SAMPLE 48QFN |
| MS3101A16S-5P | CONN RCPT 3POS FREE HNG W/PINS |
| LTC2291IUP#PBF | IC ADC DUAL 12BIT 25MSPS 64QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7664ACPZRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 16-bit Parallel/Serial 48-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:ADC SGL SAR 570KSPS 16BIT PARALLEL/SERL 48LFCSP EP - Tape and Reel |
| AD7664AST | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 16-bit Parallel/Serial 48-Pin LQFP 制造商:Rochester Electronics LLC 功能描述:16-BIT, 500KSPS CMOS ADC - Tape and Reel 制造商:Analog Devices 功能描述:IC 16-BIT ADC |
| AD7664ASTRL | 制造商:Analog Devices 功能描述:ADC Single SAR 570ksps 16-bit Parallel/Serial 48-Pin LQFP T/R |
| AD7664ASTZ | 功能描述:IC ADC 16BIT UNIPOLAR 48-LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7664ASTZRL | 功能描述:IC ADC 16BIT UNIPOLAR 48LQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
发布紧急采购，3分钟左右您将得到回复。